GSD5211P00BB General Electric Dishwasher - Instructions

Squeeze the new link to the cable hook with pliers while locking the vise grip to the cable for easier handling. Then, using the vise grip on the cable, hook the other end of the link to the dishwasher door hook

I am a 72 year old woman. The video that came with the order were perfect!! Watched a couple times and fixed it myself. My sons were definitely impressed. Thanks

I watched the convenient video and saved an old machine that I've grown to love. Plus I didn't have to pay a repair service or have to buy a new machine.
Thanks GE,
T. Dunn

With coin, to remove the end cap from the front inside of the rail, insert the edge of the coin into the side of the end cap and push the coin to the rear while rotating the end cap to the inside of the tray until it comes free. Don't force. Pepeat for other rail. Repeat to reinstall end caps. You can can now slide out the the tray. Use long nose pliers to remove old rollers and insert new roller(s) on same prong. Do all 4. Reinsert tray and end caps.

Pulled out the top tray fully, popped off the end caps. Removed the tray and placed it on the cabinet top. Popped off the old rollers and snapped on the new rollers. Replaced the tray into the dishwasher, Popped the end caps back on and I was done.

The hardest part is removing the plastic stop on the end of the two slides that support the roller rack. My unit was very old and I was afraid the plastic was brittle. Fortunately, the plastic could still be bent without breaking. You need to physically bend the plastic stops to remove. They came out easily, but you do need to apply some force.

Replacing the rollers was simple. Replacing the stops was easy once you understand how to pry them out. I would recommend trying to remove the stops with your hand only at first. You are less likely to damage the plastic.

1.Shut off the electric! 2.Shut off the water Supply. 3.Removed the two lower front panels(Two bolts each) . 4.The Water supply Solenoid is located far left up front . 5. Unplug power connector clip to the solenoid. 6.remove the two mounting bolts . 7. Use pliers to compress the rubber hose clamp And slide down the hose . 8 some small amount of water maybe in the hose a pan maybe necessary under the solenoid. 9.Gently pull the rubber hose off the nozzle. Complete installation in reverse. May The Force Be With You!

Repair was easy. However, this did not solve the problem.

The sump was very clogged with caulk like crud that we think was a chemical reaction from soap that was used the first two years. When I first started troubleshooting, the sump seemed to be the problem, so I replaced that. There was a small hose on the sump that was broken so it made sense to replace it anyhow.

When that didn't help I put the dishwasher into service mode and observed that there just wasn't enough water to spin the sprayer. Therefore it was a water quantity problem, which can be caused by either the Water Inlet Valve or the Flood Switch.

I ordered both the Water Inlet Valve and the Flood Switch, just in case. I replaced the valve first and when that worked I did not install the switch.

Installation was performed with the dishwasher still inserted in the cabinet. If you have big hands, pull the dishwasher out. With sockets and nut drivers, I was able to remove the assembly. After pulling it out enough to clear the dishwasher, I was able to get a screwdriver on the outlet side clamp and a wrench on the inlet side hose.

My old valve had a 90° elbow on it and that was difficult to remove. Installing the elbow on the new valve was just as bad. The valves don't have enough clearance to get a wrench on them to keep them from turning while the elbow is tightened.

TIP: Take a picture of the valve before removing/disconnecting anything. I don't know if the electrical connector can attach either way but I made sure to put it back on exactly the same way it was.

Without any specific directions with the part (which would had been nice. If it wasn't for my husband I wouldn't have known where to start.) I had to carfully pull the dishwasher out of the cabinet (it wasn't heavy) to unplug the power supply. Then we unscrewed 2 screws on the top and the upper arm connection came off. We replaced it with the new one, screwed it back on, reconnected the power supply and pushed the dishwasher back where it belonged. It worked out very well.
Also I want to say I am very happy with the length of time it took to get my part to me. (1 day) I was washing dishes it no time.

Thank You
Debbie Bradford
Hookstown, Pa.

Followed the sequence from on line video provided by PartSelect. Knowing the sequence and the secret of the push on nut made the replacement simple. My dishwasher is built in therefore I pulled my dishwasher half way out to gain better access and did not need to disconnect drain or water supply. Just unplugged the power and went to work.

See GE web site for repair instructions. Take out screws at top of door. Slide unit out there is a spring on each side of the door just look at the good one for details. Easy fix. About 30 minutes.

I watched the video instructions and it looked easy! The old gasket just pulled right off easily! Installation of the new gaskets was quick and easy!

Followed the very excellent instructions provided on website by Hotpoint/GE

Installation was very easy! Rack works perfectly now. Only problem...bought four sets instead of 4 parts since the order form didn't say it included 4 in each pack.