GSD4310X02BB General Electric Dishwasher - Instructions

Old cap was already off and had string on it. Cut the string. Placed end cap over. Used needle nose pliers to open metal rail a little and put in new cap. Locked right in. That was easy. Thanks again.

First I replaced the flapper valve of of off the water pump. That worked for a couple of days, then the standing water was back. After more research at your site I ran across other person who had the same problem and they ended up replacing the piston and valve assembly. After pulling the dishwasher out I was able to find where these parts were located. The piston's rubber part was half gone. I replaced it and the gasket and another flapper valve. This model has two flapper valves. One difficulty was that you have to replace the screen inside the dishwasher before you replace the housing that the piston fits in. Your site and other folks contributing their stories helphed me to solve our problem. The dishwasher works like new now. Thanks. Ralph Naddeo.

Pulled the basket out the appliance and took what was left of the roller off and replaced them and slid the basket back onto the slide channel into the appliance. Then snapped the end caps on. Almost too simple. Less money than it costs to have the service man ring your door bell.

with electric power and water source turned off,I first bailed out the water from tub then I pulled dishwasher out from under cabinet . Then I removed the motor and pump and put it on the table. I took a digital photo so I could remember exactly how everything was assembled. I checked for clogs and damage and realized that the solonoid casing had melted around the armature link assembly . I Looked at diagram for parts name and number and ordered from parts select. In the meantime I put a temporary one feed valve on hot water feed line so I could have access to hot water in kitchen while I waited for parts wich were here in a couple of days. Put it all back and it runs fine. Thank for your help

Research the problem on the internet .People suggestion was to replace the sequence switch . If this does not work replace the mother board .The sequence switch was replaced and fixed the problem .

I unscrewed the check valve, tipped the dishwasher on its face, and removed the asembly below it. Then replaced the valve flapper, cleaned out the assembly (broken champagne glass and udder nasties) then put it back the way I found it.
Then I put the new check valve on, and started the dishwasher up.

10 screws and $30 worth of parts saved me 400 bones for buying a new dishwasher.


If you have sanding water in your dishwasher check these two parts.....that check valve is the culpret.

Once the new motor and pump kit arrived. I removed the dishwasher, turned it upside down and replaced the motor and pump with the new one per the directions. Difficulty came in feeding the electrical wire/plug back through the cabinets. Once done, turned on the dishwasher, filled the tub, then manually moved the dial to drian. The water still would not drain from the tub. I searched further for the problem. Here it is; Found the air gap tube was plugged with food. Once I removed, cleaned and reinstalled the air gap, the tub drained fast and everything works great. So, I hope you folks put this up in your troubleshooting section for others to check before buying a pump and motor kit. If you had, I would have been able to check out the air gap, clean it out first before spending $140.00 for a pump and motor kit I didn't need. Anyway, lessons learned..Jeff

Replaced with a new rinse aid fill cap.

Removed the dishwasher from the cabinet. Turned it on it's top side. Removed the exit hose from the pump with a nut driver and replaced the flapper. Reconnected the hose to the pump.

The leak was coming from the drain valve shaft and I found the tips to replace the seal from this website. I was able to reach everything without removing the dishwasher from the cabinet. Once I got the cam lifter off the old push on nut was corroded so it was easy to get off. The old seal was recessed so I used the point of an ice pick to gently pry it out. The new seal was easy to push in place but the push on nut was a bear. I saw other comments about using a deep socket to push it on but I didn't have one the right size. I was able to hold the end of the shaft with pliers and pushed the nut in place using a screwdriver. Ran a short cycle and no more leak. Thank goodness for this website. Found the part easily and the other written comments were very helpful.

Replaced all ordered parts.

Removed the old one from its slot and slid the new one into it.
No instructions needed.

I watched the video and did exactly what he did. I am a novice when it comes to repairs. I learn as I go. This repair went flawlessly. Ordering was quick and easy. The part arrived quickly. The repair took less time than expected. The part was what I needed and nothing else broke or went wrong when repairing the original problem. It was a 100% success.

Removed 4 screws, took off basket covering, put new part in one turn, then replaced covering. Plumber had come out, I watched what he did, he had to order part and come back. I asked how much he didn't know but said cheaper than buying a new dishwasher. When he left I started calling around about the little plastic part that I needed. Part was $15.50. They called and said it would be $110.00. Needless to say I called them out and ordered the part myself and put it in. Took me like 6 minutes and cost $21.69. I was so mad about this situation that I even got my service call money back that I had already paid.

Old baffles lift out and new ones installed - very easy