GMB680GC129 General Electric Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Clifford from Saint Louis,, MO
- Parts Used:
- WD28X265
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
multiple rust spots on the old rack
Original part no longer made. Substitute too small by a half an inch. Corrected the problem by removing the 4 corner wheels from the old rack and put them on the new one. Now, it fits and works perfectly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- WILLIAM from EAST ROCKAWAY, NY
- Parts Used:
- WD24X10018
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers
Water Would Not Drain
Went on line to order new pump. Web site showed "parts which repaired this problem and nut and valve had very high % as the failed part". I then removed nut and valve and was able to see that it was worn as they described. This was a very easy repair and worked perfectly. It saved me from ordering a $60. 00 Pump which would not have fixed my problem. Thank you for a great help for the diys people.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- philip from bluffton, SC
- Parts Used:
- WD24X10018
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
dishwasher would not empty, your list of potential problems was an excellent guide plus the online schmatics
used tips from a past buyer
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- lawrence from lexington, NC
- Parts Used:
- WD15X93
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers, Wrench set
Old valve had hairline crack and leaking
2 screws to remove valve, turn water off, detach water line, detach plastic water outlet line, and put the new one on, reattaching everything in reverse. Electrical hookup was just two wires to solenoid. Slipped them off and back on new valve solenoid. Some difficulty getting support screws back in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from Avondale, AZ
- Parts Used:
- WD24X10018
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Dishwasher would not drain completly
Remove filter screen at rear bottom of dishwasher with 1/4 in socket, remove check valve by hand, install new check valve, reinstall filter screen. Run a load of dishes, drained completly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- terry from port clinton, OH
- Parts Used:
- WD15X93
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Wrench (Adjustable)
when dishwasher was turned on no water sprayed out the rotating arm
I diconected the electric removed water line removed 2 hex head screws pulled out inlet valve squeezed the pressure clamp and pulled off water inlet line and re assembled very easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donald from Chalfont, PA
- Parts Used:
- WD24X10018
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Dishwasher not draining, water left in bottom when cycle completed
Thought hoses were clogged. Cleaned hoses but no obstructions. Googled the problem and found many similar problems. On PartSelect, the Piston and Nut Assembly was found to be the problem 44% of the time. I ordered the part and it arrived two days later. PartSelect showed how to install it and the problem was fixed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Syl from Pagosa Springs, AL
- Parts Used:
- WD15X93
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
dishwasher would not turn on the water
took off old part, put on new part and that was not the problem.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Patrick from Hawthorn Woods, IL
- Parts Used:
- WD24X10018
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Dishwasher was not draining.
The dishwasher would drain correctly 3 out of 4 times and the original part did not appear to be in bad shape. Decided to change anyway based on posted success rate in resolving the issue and the low cost of the part. After one month of daily operation the issue has been completely resolved. Could not have been any easier!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bill from Fort Myers, FL
- Parts Used:
- WD28X265
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Lower rack had rusted through in several areas.
Pulled out the old and rolled in the replacement. The easiest part of the repair was ordering from the PartSelect website and receiving it via FedEx Ground the next day. Thank you PartSelect. Even my husband could have been successful with this.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- paul from woodbridge, VA
- Parts Used:
- WD24X10018
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
Water would not drain after cycle
After reading some of the suggestions I couldnt beleive it was that simple and easy. So I ordered the piston and nut assembly, installed it in less than 15 min. and after a rinse cycle test the problem was fixed. Thank you all for this wonderful site.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bradley from Summerville, SC
- Parts Used:
- WD24X10018
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Dishwasher would not drain
Logged on to this site. Removed 4 nuts at the very back. Removed the piston & nut assembly. The rubber piece had worn out. Reversed the process and it runs like new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Wendy from Kingman, AZ
- Parts Used:
- WD24X10018
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
Dishwasher was not draining
I removed the basket in the back of the dishwasher and unscrewed the plastic piece under the basket. I quickly screwed in the new one and now my dishwashe ris working perfectly.. We came so close to buying a new dishwasher and I am so happy I found the website describing this part. THANK YOU!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Om Prakash from Highlands Ranch, CO
- Parts Used:
- WD24X10018
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Pool of water at the bottom of the dishwasher after the cycle is complete
It is so easy and simple! Just removed the old part ( Piston and nut assembly), which is at the back of the dishwasher(inside, behind the spray arm and the heating coil) with bare hands. It needs a little push and turn , just like you removing a old stuck nut. One you remove the old nut assembly, replace it with new one. Just hand tightened is enough. Ran the dishwasher and voila...it works like a new one. No more water collection at the bottom! All it took is 10 mins + 12 dollar part + 7 dollar shipping.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Laura from New York, NY
- Parts Used:
- WD28X265
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
missing silverware basket
part came in the mail and fit the missing space perfectly. no complaints. easy fix.
Was this instruction helpful to you?
Thank you for voting!