GRSC345P00WW General Electric Dishwasher - Instructions

Installation was very easy! Rack works perfectly now. Only problem...bought four sets instead of 4 parts since the order form didn't say it included 4 in each pack.

UNPACKED WHEELS AND CLIP. USING NEEDLE NOSE PLIERS SQUEEZED WHEEL TIP TO INSERT IN WHEEL. REMOVED OLD WHEELS AND RETAINER BY HAND. INSTALLED NEW WHEELS INSTALLED AND NEW RETAINERS

Removed all 8 wheels and inserted the new one after inserting the axles into each wheel. Replacement wheels had a much better connection to the bottom rack and do not anticipate any problems in the future.

I watched the video instructions and it looked easy! The old gasket just pulled right off easily! Installation of the new gaskets was quick and easy!

There was a video on the page as the part. Done in a flash. The axle was a little hard to get into the wheel so I soaked it in a little hot water and it whet in like a charm.

This is a very simple fix. The majority of work comes from getting the unit out of it's enclosed space so it can be worked on. Once the dishwasher is out in the open, lay it on it's side, and simply unscrew some metal clamps, pop out the bad part, replace it with the new, reattach the pieces and clamps, and start putting the unit back in place.

I'm just happy I was able to actually find the part to begin with, and then to make the changes myself is a very rewarding feeling. Instead of missing time from work and shelling out $150+ to have an appliance repair man come out to do the work, I spent $20 for the part, and maybe an hour total to make the repairs.

I'll be back to this site in the future if/when other parts on other appliances go bad.

from the information previous customers had written.
it saved a lot of fustration and time
and best of all the dish washer does not leak.

removed both corner baffles, also door gasket was bad, all parts were easy to order and install, the customer service was excellant with all my questions and concerns to get the right part and the parts arrived in just two days, thank you

Removed the white end of the top track. Pulled off the remnants of the rack roller. Slide the rack roller wheel into the track and popped the other end on the top rack (looked at the other rack rollers to see how it fit.) After that, I put the end back on the track.... Note what is the top and what is the bottom of the track end. Realizing that there is a wider area on the track to slide part of the white track end through to get it on without much effort.

Took out old one and put in the new one. Not hard at all. Thanks

Removed the 7 screws from inner side of door; removed set screw from handle; removed inner door cover; pulled old part out; pushed new part in and Voila! Replaced all screws, no problem. Thanks for your great customer service!

The solenoid and linkage was easy to disasemble, but getting the retainer (push on nut) off was difficult without removing the motor and pump. Once removed it was a snap. Getting the pump/motor back onto the pipes was near impossible from underneath. I had to remove the dishwasher from under the countertop to get it back correctly. I would reccomend doing this for this repair, as it made life a lot easier. Unwiring and removing the water supply line was not a problem either. WORKS AS GOOD AS NEW!

I first shut off water supply and disconnected the water line and drain hose to the disposal. Then I pulled the dishwasher out from the cabinet unplugged the electrical wire from the wall and laid it on it's back side. I then laid out the new motor and compared parts to parts. It was a direct replacement of the same motor except for very minor changes. I unscrewed the support bracket, then unscrewed the bottom clamp that joined the motor and the rubber connector to the dishwasher. I also decided to replace that part also. That part was removed by using my hand to unscrew it. It has large threads that are not very recognizable when looking at the part. It unscrews counterclockwise like a normal screw. You have to hold the inside piece while you screw the new one back in place. I put it as tight as I could by hand. I would recommend doing so on all motor replacements due to that part not looking so good and if it leaked you would have to take everything apart again to change it out. That part is a separate purchase and it is not included with the kit. Then I took the other clamp to the plastic connector off. I then unplugged the electrical connections, there were only two and they were both exact connections for the replacement motor. After that the entire motor was separated from the dishwasher and I went slipped the new motor into place connected two clamps and made sure everything was reconnected. I slid the dishwasher in place, reconnected the power wire, the drain hose, water supply. I checked for leaks after restoring water pressure. Then ran the dishwasher through a complete cycle and it works just fine. Total repairs cost about 150.00 and the dishwasher appears to be brand new again. I took one look at the diagrams and never had to refer back to them. They had plenty different diagrams and the first option was mine and that was all I needed. I would recommend this option to anyone.

Fiddled with the rollers until figuring out how to remove them. Hardest part was getting the stops off the ends of the roller guides. Replaced rollers, replaced rack, replaced ends of roller guides. Voila

As the washer is slightly undersized to perform correctly, following standard instructions to replace the drain valve staff seal and retaining washer I wound Teflon tape between the retaining ring and washer to slightly increase pressure on the washer and seal the opening.