GMB919JC119 General Electric Dishwasher - Instructions

replaced pump and motor with new one. worked but pump would not empty the water. ordered additional parts check valve,seal and box that check valve screwed into. did not fix problem. Got to looking at replacement pump and discovered thet discharge solonoid was not completely opening the discharge port. I could hold it down manually and the machine would empty. I reported the problem to parts select and they without question shipped me a new pump and motor. took the dishwasher out of the wall again and swapped them out, and now it works fine. the repair was easy and simple. the difficulty was taking the dishwasher out and reinstalling it 3 times. I will use parts select again if the need arises.

Remove lower panels, turn off hot water supply, Turn off breaker to dishwasher. notice how power connector is orientated and how valve is mounted to chassis of dishwasher and remove Molex connector which supplies power to valve. The power to the valve is 120VAC when the timer gets to the appropiate cycle I measured the valve with no connector attached with DVM set to Diode or ohms setting and got about .825. I measured the NEW part and measure about the same. Have towel under valve hoses for small amount of water will come out. remove small diameter hose , inlet water supply, remove 2 screws holding part with nutdriver to remove valve which exposes the black hose attached to valve. Hose has a hose clamp, use pliers to remove. good time to check and clean hoses. I unwrapped a coat hanger to run through the hoses for debris. to INSTALL reverse the above. clean water away from floor with towel. Turn on hot water supply, check for leaks, I did not have any leaks. Turn on breaker. You can stick a stubby screwdriver into the door close switch of front door which enables you to turn on (swing arm) dishwasher with door open to check water pressure. I have a great deal more water pressure and water from jets spray much higher than before. Old valve was clearly bad, but solenoid of valve still worked, which sucks in the arm when energized. I used a DVM on the 2 wire connector on valve to check for 120vac when cycle turns it on-measured good. I still don't have quite the same cleaning as before. It is 80% better, but something is still not right. My wife put in one of those pot cleaners (red) mesh plastic thingy on top rack--and found pieces of red mesh plastic in debris area, cleaned it out as best I could removing the 2 covers, but not sure valve is opening there or debris is clogged in there which sends pieces of food, etc. through hose to garbage disposal. Hose wasn't clogged. Cleaning better but wife is still saying not as good. The Pump is running good, cleaned dust and dirt out of pump with vacuum. 10 years old, thinking of removing dishwasher from counter and checking the pump area or change it.

Pulled the dishwasher out from under the counter using a little rug to keep the metal feet from scratching the tile. It is surprisingly light. Old motor and pump are held in mainly by pipe clamps, easy to remove once the washer has been pulled out and turned on its side.

The instructions that came with the pump kit show how to set it up for several different dishwashers. Once you figure out which one you have it is quite easy to set it up. Mine leaked when I first started it up. I pulled it back out and re-tightened the large pipe clamps and it now runs dry.

The dishwasher runs quieter and the dishes come out clean now.

took the moter off and the impellar off replaced the impeller .back and turn the washer back on but it still wouldnt .wash .the moter wouldnt turn .so had the moter tested and it was the moter . found out how and what to look for on you tube .it was a big help in how to fix your washer .typed in model and what kind portable .it was easy .thank you for haveing my part also .and shipping was real fast .

I pulled the old basket out with my right hand and inserted the new basket with my left hand! HA! Maybe 5 seconds!

Just plopped it in, it fit perfectly! I love it! Very easy to order the part, and very fast shipping! I order it and it took a day to get to me!

Just set it in as it was exactly as described and ordered.

After running a test cycle and realizing the pump was working but not pumping all the water out, I checked the troubleshooting guide and parts list.
I found there was a check valve at the back of the machine and when I removed it I saw it was split causing the water to return into the unit. I ordered and replaced the check valve and the unit is back in perfect operation.

Remove old piston assembly with screwdriver and tapping hammer inside the machine and screw the new part in hand tight, all done works fine

I read the reviews on line and followed the advice the part was easy to find and easy to replace once I got the screen off it came right out with a twist. and right back in reverse order, I fired it up and it drained, yay! no more stinky mess and no call to the appliance repair guy,

i unscrewed the 4 screws in the back, took off the guard thing, and unscrewed the existing part with my hand. put new part in and ran dishwasher. the part did not fix the problem, now i'm on to maybe replacing solenoid? i have no idea. this part was simple to replace though. hope i can fix this issue, i need my dishwasher to run right!

remove the four screws in the back of dishwasher on the inside. Remove screen. Remove the piston nut assembly for the check valve. Re-install the screen and four nuts and your done.

Had to pull off the front cover where my problem was. Discovered a burnt out switch of some sort, looked it up on your site and found the part. It seemed expensive so I searched a few more sites and discovered you had the cheapest price. I ordered the part on Monday morning and used the cheapest shipping. 5 to 7 days is what i was informed of so i figured it was worth the wait. I got home from work Tuesday and the part was at my door (wow!) I still had my dishwasher torn apart so I put the new part in and about ten minutes later I was washing a load of dishes! I would refer partselect.com to anyone. Thank you! I hope I never need to use your site again but if I do I've got it saved in my computer! (-:

After researching for a few minutes on this site I was pretty confident that the problem I was having was a faulty check valve. I removed the 4 screws holding the cover in place at the back of the dishwasher tub, twisted out the check valve and saw it was obviously shot. I ordered the correct part and 2 days later I had the dishwasher working like new. Installation was a simple as could be....twist in the new valve and reinstall the 4 screws.

Partselect was the only one that had the correct solution. The Piston and Nut assembly fix the problem. The washer on top of the piston was worn and it would not fully close. Replace the piston and nut assembly within 15 minutes after I found it.Shipping was supposed to be within 3 days. The part came the next business day during the thanksgiving holiday. WOW