GMC4439KW119 General Electric Dishwasher - Instructions

Removed old basket, put new one in. New basket fits but it is larger then the old one so it takes up more room leaving less room for dishes. My dishwasher is apartment size.

Service from PartsSelect was very prompt.

Very simple repair: assemble the wheel/clip assembly. Attach to lower dish rack.

I was very happy with the fast delivery by PartSelect.

did it by hand, carefully flair out the plastic piece only enough to slide it into the metal rail.

Once realized needed to open the wheel rail a little to remove wheel stop, it wasn't too difficult. Took about 20 minutes. Part came in a couple of days and was the correct part. Was disappointed that a similiar part, looked the same on the web site costing about $54.00 plus shipping, ended up costing about $100.00. Contacted customer service, said I needed to contact the factory. Seems like they should have researched the problem, Andy Duer

Pulled the lower left side end of the old door gasket out of door gasket retaining slot and slowly and evenly continued to work my way around the door pulling the door gasket out of the retaining slot until I reached the end. I installed the new gasket into retaining the retaining slot beginning on lower left side and then slowly and evenly working my way around the door inserting the new gasket into the retaining slot. I was careful to make sure the two cutout portions of the new gasket's retaining edge were correctly positioned in the lower corners of the door.

remove water connection; shut off circuit breaker ; follow the suplied directions; reassemble washer . job done - leak gone. Wife happy.

Removed screws on the drain pump filter screens at the back of the dishwasher, unscrewed the check valve, screwed in the replacement unit, and re-affixed the filter screens.

I lived with the drain problem for 6 months and reviewed on line trouble shooting which all pointed me to a pump or solenoid valve problem. I pulled the unit and disassembled everything before noticing that the rubber washer/stopper at the top of the check valve had erroded away and was not preventing water from pumping back into the cabinet when the drain pump kicked on. Always check the condition of this check valve first if you dishwasher is not draining properly. It was so easy once I found the bad part.

We ordered the pump kit by model number and it was a perfect match.(It was on our door step in 2 days with normal shipping!) Three bolts and a couple of electrical connections later and the pump was off The install was just as easy. The instructions were very easy to follow.It's great to find a company these days that knows what it is doing and does exactly what it says it will do.
Kudos and thanks!

We ordered our motor and pump assembly. When it arrived we followed the instructions that came with it. We had no problem with the instructions. We found it to be really easy. I was very happy since this happened 4 days before Thanksgiving. Thanks for the easy instructions, my husband got my dishwasher repaired in plenty of time for our Thanksgiving family get together.

As suggested. Pull washer, remove screws from top and replace with new part. Very simple and easy if you follow steps furnished by this site.

I used the pump/motor replacement kit. It was a very easy repair and the parts were a direct replacement with no modification necessary. I saved over $300.

I made a substitute cable that worked ok, but was a bit loose. When the new cable part came in I simply unhooked the substitute and hooked the new part in its place. The two spring ends slip into a hole on the cable connector. The cable loops under a plastic pulley and the far end piece fits over a small retainer. Actually, unbolting the bottom case parts and bolting them back on took more time than replacing the broken cable. The door works fine now.

I removed the screws from inside door panel. Took door panel out. Noted the way the old gasket was placed, removed it and replaced with the new gasket. Replaced the door panel. Felt pretty proud of myself until I realized that the door lock wouldn't work when I was going to run it. I have now removed the door panel again and am trying to get the door lock lever to work.

Removed all 8 wheels and inserted the new one after inserting the axles into each wheel. Replacement wheels had a much better connection to the bottom rack and do not anticipate any problems in the future.

Followed the very excellent instructions provided on website by Hotpoint/GE