405062 General Electric Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- tim from prior lake, MN
- Parts Used:
- WD12X10163
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The soap dispenser would not close.
This was simple. I took the door apart with a portable screw driver. Then I detached the wires and unscrewed the old module and replaced it. I then put the door back together, loaded the dishwasher and it cleaned my dishes. Even for this `old dog' it was easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Fitchburg, WI
- Parts Used:
- WD12X10304, WD35X20994
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
End Cap and Wheel axle were worn or broken
This repair was a snap. The parts, though not identical to the original, fit perfectly. I was able to snap both the Rack Slide Cap and the new wheel axle to the existing washer cage and the machine works great now.
Thanks for the quick delivery and great website!
Thanks for the quick delivery and great website!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Pamela from Bakersfield, CA
- Parts Used:
- WD22X10046
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Wrench (Adjustable)
Broken middle spray arm
Unscrewed the screw holding it in place and removed it, out the new one in place and screwed it on. Very quick and simple.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Barbara from Georgetown, CO
- Parts Used:
- WD15X10003
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
Plastic part of inlet valve cracked
Hired my neighbor, who is a plumber.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Laverne from Roselle, IL
- Parts Used:
- WD12X10278
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
pieces that attach the wheels to the lower rack kept falling off
Ordered the new parts and attached to wheels on lower rack. The old pieces clamped on and the plastic stretched out and would not hold any longer. The 8 new pieces have a slightly different design, were easy to intall and I believe will never loosen up.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Suzanne from CHEYENNE, WY
- Parts Used:
- WD12X10109, WD12X10061
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Old parts showing wear
Watched a YouTube video on disassembly, parts replacement, and reassembly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Chris from GREENVILLE, SC
- Parts Used:
- WH23X10028
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Socket set
Did not drain water
Per ps video. Really easy. Disconnect power, Remove front lower panel, remove Power leads, 2 installation bolts, remove 2 spring clamps on feed/exit hoses,reinstall.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Alice from BLAINE, MN
- Parts Used:
- WD12X10122
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
cap had melted mi
Unscrew the old one and screw in the new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Wayne from PALMER, MA
- Parts Used:
- WD35X20994
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Rollers and axles were worn out
Removed the stops at the end of the upper rack, removed the old rollers. Replaced with new rollers and installed the stops back in place. Very easy, finished in less than 15 minutes. Replacement rollers very much improved with design from the original rollers.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Eric from EAST MEADOW, NY
- Parts Used:
- WD14X10009
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers
Plastic hinge arm link broke
Squeeze the new link to the cable hook with pliers while locking the vise grip to the cable for easier handling. Then, using the vise grip on the cable, hook the other end of the link to the dishwasher door hook
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Christopher from GLEN ALLEN, VA
- Parts Used:
- WD05X10010
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Wrench (Adjustable)
Dishes were not drying inside the dishwasher after the dishwasher cycle completed
The installation video that is on the website with the part is very helpful & easy to follow. The wires that attach to the heating element & the nuts that hold it in place are actually located a few inches off the ground so I didn't need to tip the machine over to pull them out & unscrew the nuts. All I had to do was unscrew the screws that hold the dishwasher in place under the counter next to the sink, pull it out & was able to reach the wires underneath it.
The actual repair took me less than 30 minutes, I marked it as 30-60 because during the somehow the water line going to the dishwasher had come loose from under the sink (not at the dishwasher) & because of this I had to stop midway to deal with some loose water & tighten things back up. I would recommend following the video, there really isn't much more to add that would be helpful.
The actual repair took me less than 30 minutes, I marked it as 30-60 because during the somehow the water line going to the dishwasher had come loose from under the sink (not at the dishwasher) & because of this I had to stop midway to deal with some loose water & tighten things back up. I would recommend following the video, there really isn't much more to add that would be helpful.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dominic from NORTH READING, MA
- Parts Used:
- WD08X10075
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers, Socket set
Had a slight leak lower center front Solved
Great
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Harinder from CHESTERFIELD, NJ
- Parts Used:
- WD12X10163
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
detergent dispenser was not closing and dishes were dirty
followed the video step by step which was very well expalined and was able to complete the install
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Greg from GROVE CITY, OH
- Parts Used:
- WD01X10099
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
The plastic part was broken from the pulley
After I unscrewed it from the counter and took off the front panel I first went to the garage to turn off the power to the dishwasher. I then pulled it out a little bit at a time. I didn't want to take apart any hoses or unplug electrical wires from connectors if I didn't have to. I then looked underneath and noticed that only one pulley spring was off and the plastic piece was broken. So when I received it in the part in the mail I took of the plastic part from the pulley. I just reused the original wire pully. I reached back with the spring to hook it back on with some difficulty and then hooked the piece back on and it was done. I placed everything back and switched the power on and its good to go. Nice job to do myself and watch a Youtube video on how to do it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ron from SOUTHPORT, NC
- Parts Used:
- WD14X10009
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Broken spring on door.
See GE web site for repair instructions. Take out screws at top of door. Slide unit out there is a spring on each side of the door just look at the good one for details. Easy fix. About 30 minutes.
Was this instruction helpful to you?
Thank you for voting!