405011 General Electric Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Tony from Auburn, CA
- Parts Used:
- WD15X10003
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Wrench (Adjustable)
Water leak from inlet valve
Had to pull the dishwasher from under the counter to access the water inlet valve. Disconnected the hoses from the inlet assembly. Removed the inlet assembly from the dishwasher frame. Installed the new assembly and reconnected the hoses. Plugged the dishwasher in, selected a cycle to run to check for leaks.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from Terra Ceia, FL
- Parts Used:
- WD15X10003
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Socket set, Wrench set
The water valve went out
I took the old one off and replaced it with the new one, which fir perfectly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Greg from GROVE CITY, OH
- Parts Used:
- WD01X10099
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
The plastic part was broken from the pulley
After I unscrewed it from the counter and took off the front panel I first went to the garage to turn off the power to the dishwasher. I then pulled it out a little bit at a time. I didn't want to take apart any hoses or unplug electrical wires from connectors if I didn't have to. I then looked underneath and noticed that only one pulley spring was off and the plastic piece was broken. So when I received it in the part in the mail I took of the plastic part from the pulley. I just reused the original wire pully. I reached back with the spring to hook it back on with some difficulty and then hooked the piece back on and it was done. I placed everything back and switched the power on and its good to go. Nice job to do myself and watch a Youtube video on how to do it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Barbara from Georgetown, CO
- Parts Used:
- WD15X10003
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
Plastic part of inlet valve cracked
Hired my neighbor, who is a plumber.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Eric from EAST MEADOW, NY
- Parts Used:
- WD14X10009
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers
Plastic hinge arm link broke
Squeeze the new link to the cable hook with pliers while locking the vise grip to the cable for easier handling. Then, using the vise grip on the cable, hook the other end of the link to the dishwasher door hook
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jonni from VACAVILLE, CA
- Parts Used:
- WD28X25960
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
leg fell off of bottom rack.
Slid it in. Very easy and the replacement part is built better than the original part.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Edward from GRAND BLANC, MI
- Parts Used:
- WD35X21038
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
NONE
UNPACKED WHEELS AND CLIP. USING NEEDLE NOSE PLIERS SQUEEZED WHEEL TIP TO INSERT IN WHEEL. REMOVED OLD WHEELS AND RETAINER BY HAND. INSTALLED NEW WHEELS INSTALLED AND NEW RETAINERS
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Amelia from PEORIA, IL
- Parts Used:
- WD28X25960
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Rack was rusted and broken.
It was a very simple replacement. I took the old one out and rolled the new one in. It took less than 5 minutes!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- robert from HAYMARKET, VA
- Parts Used:
- WD08X10018
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers
Leaked front right side
Followed the instructions that came with the my order
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- helmut from EAST KINGSTON, NH
- Parts Used:
- WD35X21038
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Lower wheels kept falling off
Installed new lower rack wheel kit
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John C from SPRINGFIELD, VA
- Parts Used:
- WD28X25960
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Bottom dishwasher rack rusted out
Simple install- just roll it in. Fit perfect. Better design than OEM part. Perfect.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sheila from DEERFIELD, IL
- Parts Used:
- WD35X21038
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
One axle cracked and broke off; another wheel was had fallen off and was distorted when it hit the heating element.
Removed all 8 wheels and inserted the new one after inserting the axles into each wheel. Replacement wheels had a much better connection to the bottom rack and do not anticipate any problems in the future.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- tim from prior lake, MN
- Parts Used:
- WD12X10163
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The soap dispenser would not close.
This was simple. I took the door apart with a portable screw driver. Then I detached the wires and unscrewed the old module and replaced it. I then put the door back together, loaded the dishwasher and it cleaned my dishes. Even for this `old dog' it was easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jean from White Plains, NY
- Parts Used:
- WD12X10122
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
missing cap
I placed the missing cap into the dispenser.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Wayne from PALMER, MA
- Parts Used:
- WD35X20994
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Rollers and axles were worn out
Removed the stops at the end of the upper rack, removed the old rollers. Replaced with new rollers and installed the stops back in place. Very easy, finished in less than 15 minutes. Replacement rollers very much improved with design from the original rollers.
Was this instruction helpful to you?
Thank you for voting!