41410119 General Electric Dishwasher - Instructions

1. I pulled off the plastic end caps to the top rack that allows the roller wheels to be pulled out of the aluminum rails. You need to push in the raised edge of the plastic caps so they clear the rail slot in order to remove them. This takes a little bit of finger pressure or you can use a flat-edge screw driver to pop them out.
2. Once this procedure is completed, you simply remove the rack and rollers from both rails and remove the old roller wheels and replace them with the new ones.
3. I used a phillips-head screw driver to tighten up the rail wheels before re-installing the top rack into the rails and then re-inserted the end caps. Pliers are handy to help get the end caps back into the rail slots.
4. I finally used a silcon spray on all of the rolling parts of the top tray assembly for lubrication.

I pulled the dishwasher out and detached the drain hose. I attached the new drain hose after cleaning out the connection to the garbage disposal.

Now my dishwasher doesn't stink anymore!

Disconnected the electrical, water supply and drain. Pulled unit out from under counter, tipped it on its side and replaced the motor/pump unit. tipped it back on its legs put it back under the counter connected the water supply, drain and electrical. All went well. The unit performs as it should. it took about two (2) hours without rushing through it.

Replaced door seal, right and left corner seals. Piece of cake. A five minute job.

Thanks

Old cap was already off and had string on it. Cut the string. Placed end cap over. Used needle nose pliers to open metal rail a little and put in new cap. Locked right in. That was easy. Thanks again.

Pulled the basket out the appliance and took what was left of the roller off and replaced them and slid the basket back onto the slide channel into the appliance. Then snapped the end caps on. Almost too simple. Less money than it costs to have the service man ring your door bell.

I unscrewed the inside of the dishwasher door and clearly saw the old interlock switch. This dishwasher has two, but it was obvious that one switch worked and one didn't (one switched was permanently pressed in). I removed the old interlock switch. It was tricky to pull out and I felt like I was going to break it but after watching youtube videos, I was pretty sure you just have to pull hard. I easily put the new switch in, reattached the dishwasher door, and it works perfectly!

After disconnecting the supply and drain hoses I unscrewed the security screws and slid the unit out of it's space under the counter. I tipped the machine about 30-45 degrees to one side and examined the underside. I noticed a solenoid that appeared to control a valve leading to the drain tube. I cycled the washer through a wash cycle and noticed that the solenoid never activated. I removed the solenoid and found it filled with debris. I cleaned it out and reinstalled it, but it still did not function. I ordered the part from PartSelect.com because they had the clearest description of the part I needed. Delivery was quick and installation took only a few minutes. After hooking everything back up and sliding the machine back in place, it works like new.

Took off the lower faceplates. Removed the old eyelet assemblies (one broken, one not) and replaced both with new ones. Very easy to repair.

Once the new motor and pump kit arrived. I removed the dishwasher, turned it upside down and replaced the motor and pump with the new one per the directions. Difficulty came in feeding the electrical wire/plug back through the cabinets. Once done, turned on the dishwasher, filled the tub, then manually moved the dial to drian. The water still would not drain from the tub. I searched further for the problem. Here it is; Found the air gap tube was plugged with food. Once I removed, cleaned and reinstalled the air gap, the tub drained fast and everything works great. So, I hope you folks put this up in your troubleshooting section for others to check before buying a pump and motor kit. If you had, I would have been able to check out the air gap, clean it out first before spending $140.00 for a pump and motor kit I didn't need. Anyway, lessons learned..Jeff

Took the screws out of the back of the doorl located the switch and replaced it put screws back in and it was fixed

Removed panel to access the interlock switches. There were two. The button on one switch was fine and the button on the other would not depress. Ran a continuity test and it failed. The switch also had a burnt smell

Replaced all ordered parts.

I simply removed the front toe kick panels.
The solonoid is staring you in the face.
I removed the small nuts on back side of the solonoid bracket and removed the retaining clip and springs.
I installed the new solonoid and was very surprised how easy it was.

I DID turn the power OFF at the breaker panel prior to starting the repair.

I first removed four screws holding the two cover panels attached to the dishwasher front at the bottom. Next I removed the broken cable and put everything back together that had sprung apart when the cable broke. Then I inserted the two door springs ends into the cable slots. Next I pulled on the springs to create slack and attached the cable / eyelet assembly to the protruding tab on the dishwasher frame. After attaching both sides the door works perfectly.