400910 General Electric Dishwasher - Instructions

The repairman offered to fix the dishwasher at a cost of about $200 or supply the water inlet valve for $85. Google led me to PartSelect.com where I easily found the correct part for $45. I received the part in 2 days by FedEx ground.
The hardest part of the repair was removing the dishwasher from the cabinet. I took the dishwasher out a short distance to the patio where I replaced the water valve...about 10 minutes.
I then made a makeshift connection to an outdoor water hose and connected the electricity and ran the dishwasher while out on the patio through a short cycle to make sure of the repair and check for leaks.
Then reinstalled into the cabinet...total time about 2 hours.
Thank you PartSelect.com

Easy. I removed the dishwasher and all water from inside. After laying the dishwasher on floor, the valve flapper was installed using a pair of pliers. I then set the unit upright, and removed the rear screen from the inside back of the unit. This part has 4 nut screws, and runs the width of the unit. Under the screen, the Piston and Nut Assembly for Check Value simply unscrewed. When I looked at it, I knew this would do the trick. I simply screwed the new one in, and re-installed the dishwasher. After the first cycle, I smiled thinking of all the $$$ I saved.

Parts Select is great :)

Took four screws out, unscrewed the piston & nut assembly by hand installed the new one. Cycled the dishwasher & it worked perfectly.

Unplugged unit, unscrewed screws on top of dishwasher attached to countertop, undid water supply and drain hose that goes into tee with garbage disposal. Using crescent wrench turned front leveling screws up all the way and slid/rocked dishwasher out from under the counter - I had no problem leaving back leveling screws down. Turned dishwasher over on some towels (it WILL leak some water so spread out some towels!) so it was oriented like the directions that came with pump and motor. The directions were good, although color or a picture might have been more helpful. CHECK the new pump/ motor unit CAREFULLY for any loose debris from packing etc. I had a small piece of plastic that was in the top of the motor that goes in the dishwasher bottom that rattled around after I installed everything and put it back. I was able to get to it from the drain assembly in the tub but it made a heck of a racket at first. All in all, I had a great experience. I'm glad I ordered the pump and motor even though I only thought I needed the drain solenoid because when I took the old unit out, the prop on the old impeller was almost gone. Easy to order, good customer service (I called with a question and talked to a wonderful customer service representative!), good directions and easy to do. I'd say a 4 out of 10 in terms of difficulty. Thanks PartSelect!

Removed the lower rack and installed new wheels with clips

Removed old rack replaced with new one which was an exact duplicate. Mama's happy; everybody's happy.

Inserted wheels on socket and then into the dishwasher rack.

First I opened the package and screwed the new dispenser cap into place.

Removed door panel. Removed old door seal and cleaned seal recess. Installed new seal. Replaced door panel on door and ran a cycle to check for leaks. Readjusted door latch to correct small leak. Ran another leak test. Job complete and wife is happy!

Disconnect water line and screws (2) holding dishwasher under cabinet, and clamp for wastewater line. Pulled dishwasher out, turned on its side, and removed pump. Disassembled pump per instructions (great instructions) and installed new parts. Reversed to reassemble and except for a loose clamp that leaked (I tightened) it went well. Just under 1 hour.

First I turned power to dishwasher off at fuse box.then,removed inside panel inside dishwasher about six screws.examined the control switch assembly and removed two screws that hold it into place.carefully removed two wire housings.Then located the part no.and model no.on the control panel.ordered new part online.The new control panel assembly arrived the next day.Installed it right away.Our dishwasher works as good as new. Thanks

Turn off power at breaker box.
Remove lower covers and 2 screws into counter top.
Verify sufficient length on water and electrical connection to allow sliding dishwasher out approx. 2/3. I disconnected the electrical at the j box on the dishwasher. If you must disconnect the water line, shut off supply, usually located under nearby sink, and provide a rag or sponge for small amounts of water left in supply line.
Carefully pull back the insulation to expose two screws on top where water line runs into the center.
Pull the top tray part way out and reach in to hold the spray arm while removing the screws. The spray arm will easily drop out.
Hold the new spray arm in place making sure the raised screw posts push into the holes, then reinstall the two screws. Done. Pull insulation back into place, retape if necessary. Reconnect electrical and water if necessary.
Slide unit back in, checking alinement. Rescrew to counter top and reinstall lower covers. Task complete. 15 mins if prepared. 30 mins if both elect. & water are disconnected and you are somewhat hesitant.

installed part on inside end of rail. no tools needed. original part wouldn't stay on rail. finished in 2 minutes
wife happy

We knew roughly how we needed to put the cap on the rail, but our technique of simply forcing it in the end of the rail wasn't working. The trick is to bend the moveable part of the plastic cap inward while you're sliding it in, and it clicks right into place.

The location of the cap we were replacing was the upper back left, which made it a little tricky to reach back there and insert it, especially for a bigger guy like myself. We took the bottom rack out and my smaller wife was more easily able to lean in the dishwasher and reach back there to insert it.

The Solenoid black plastic had melted around the solenoid shaft. I unplugged the solenoid, removed 2 screws,then one C clip and pulled the the unit out. The new solenoid is difficult to install all together as the shaft it goes on holds it all together when both springs are installed - - so I installed in one piece, with the 2 screws, except for the white plastic thing, the C clip that holds it on the shaft, and one of the two springs - - these three items went on separately. I wanted to thank the help your expert gave, but I couldn't figure how to do that.