40530117 General Electric Dishwasher - Instructions

Pulled out the top tray fully, popped off the end caps. Removed the tray and placed it on the cabinet top. Popped off the old rollers and snapped on the new rollers. Replaced the tray into the dishwasher, Popped the end caps back on and I was done.

Watched the video and swapped out the parts when they came. One of the arms that one of the rollers attached to was rusted and swollen had to remove the plastic coating and sand in order to get a good roller fit. Went super easy

Without any specific directions with the part (which would had been nice. If it wasn't for my husband I wouldn't have known where to start.) I had to carfully pull the dishwasher out of the cabinet (it wasn't heavy) to unplug the power supply. Then we unscrewed 2 screws on the top and the upper arm connection came off. We replaced it with the new one, screwed it back on, reconnected the power supply and pushed the dishwasher back where it belonged. It worked out very well.
Also I want to say I am very happy with the length of time it took to get my part to me. (1 day) I was washing dishes it no time.

Thank You
Debbie Bradford
Hookstown, Pa.

Door seal was brittle and flat.
Not a hard job to do just having to keep making sure the seal did not pop out on the bottom corners of the door. The seal would tare easy so have to be careful. Before you remove the old seal on the bottom of door there is a 4 inch space between the ends of the seal. Mark the spot with marker so you know where to start placing the new seal.
Baffles were orginaly put in place with plummer putty, do not use this. Get GE clear seal is the best will hold forever but will come loose with a good tug. easy to clean out when replacing baffles again. Do not use any sealent when inserting the door seal just push into opening. Make sure you support the door when pushing down on door to put the seal in the slots.
The hardest part is the bottom corners the seal tends to slip out I found that if I streached the seal over the openings and continued on and come back to the corners it was easier to make the seal slip in.

Removed the corner baffles by lifting up and out. Cleaned the area and pushed new replacements in position.

Removed door seal by pulling on the end.
Press new seal in to the slot. Work in to slot a tree ound door.

I used Partselect.com website to educate myself on parts needed for my model of dishwasher. Also reviewed repair instructions by others on the website and learned repair and replacement was straight forward and simple. I ordered parts from Partselect.com, they came promptly, and were the correct parts. Based on the repair instructions, I removed the fascia panel at the bottom of my dishwasher to expose the cable and spring setup for my model dishwasher, cleaned the area and installed the new parts - it took only a few minutes - then I replaced the panel and secured it with the sheet metal screws that were holding it in place. I opened the dishwasher door. My wife had already cleaned the corners of the tub where the old baffles had been, so I pressed the new baffles into place with my fingers - no tools were required for baffle installation. Dishwasher is back in service; thanks to the information, parts and prompt service provided by Partselect.com ! My wife is pleased and so am I.

researched the problem, listened to you tube, ordered the parts
and did the repair. Very easy to do, only took a few minutes.

1 - unscrew that holded the machine in place, these screws were on the top of machine.
2 - pull out machine about 5 inches.
3 - unscrew the cover at the bottom cover. there were 4 screws, 2 on the left and 2 on the right.
4 - connect 2 cables in series with 2 springs.
5 - hook one end of 1st cable to the left pin and the other end of 2nd cable to the right pin.
6 - slide both cables lay on both wheels.
7 - Tight all 4 screws back to their place and push machine in place.
8 - tight the last 2 screw which hold machine in place.

Open door, remove lower wash rack, remove 4 screws holding screen in rear of inside tub with 1/4 inch socket. Unscrew piston and nut assy for checkvalve, sounds like a mouthful but it is only 1 part. Checkvalve has 2 small ears on it which allow you to twist it out, it has treads on it. Flapper on check valve flapper rots away and water pumps back into tub instead of being routed to drain line to garbage disposal. Part with shipping was just over $20.

removed the end caps and took the rack out of the dish washer.

found right front rack roller bad and replaced.

slide rack back into dishwasher and replace end caps.

Part delivered in 3 days

1. remove kick panel (4 screws) - remove broken cable - install new cable - reinstall kick panel - done.

2. snap retainer hub into wheel - snap retainer onto rack - done.

removed both corner baffles, also door gasket was bad, all parts were easy to order and install, the customer service was excellant with all my questions and concerns to get the right part and the parts arrived in just two days, thank you

Remove the bottom two panels below the dishwasher door. There are two phillips screws and two nut screws.

Replace the broken cable by first hooking the cable to the side of the dishwasher. The other end of the cable assembly with two holes hooks up to the two large springs which keeps the door in balance. Hook one spring at a time to the cable assembly.

Reassemble the two bottom panels with the four screws.

YOU ARE DONE - Congratulations, you just saved $125 which is what the plumber quoted me.

Removed the 7 screws from inner side of door; removed set screw from handle; removed inner door cover; pulled old part out; pushed new part in and Voila! Replaced all screws, no problem. Thanks for your great customer service!

The cable attachment comes with the two hole loop assembly that the springs hook into. With the lower panel off and the door closed, the other end of the cable assembly hooks onto the fitting on the side of the door. No tools required except the phillips head screw driver to take off the lower panel.