40440129 General Electric Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Jeffrey from Springfield, VA
- Parts Used:
- WD12X10327
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Old roller wheels were starting to stick due to cracking
1. I pulled off the plastic end caps to the top rack that allows the roller wheels to be pulled out of the aluminum rails. You need to push in the raised edge of the plastic caps so they clear the rail slot in order to remove them. This takes a little bit of finger pressure or you can use a flat-edge screw driver to pop them out.
2. Once this procedure is completed, you simply remove the rack and rollers from both rails and remove the old roller wheels and replace them with the new ones.
3. I used a phillips-head screw driver to tighten up the rail wheels before re-installing the top rack into the rails and then re-inserted the end caps. Pliers are handy to help get the end caps back into the rail slots.
4. I finally used a silcon spray on all of the rolling parts of the top tray assembly for lubrication.
2. Once this procedure is completed, you simply remove the rack and rollers from both rails and remove the old roller wheels and replace them with the new ones.
3. I used a phillips-head screw driver to tighten up the rail wheels before re-installing the top rack into the rails and then re-inserted the end caps. Pliers are handy to help get the end caps back into the rail slots.
4. I finally used a silcon spray on all of the rolling parts of the top tray assembly for lubrication.
Was this instruction helpful to you?
Thank you for voting!
Water leak at lower right corner of door.
Replaced door seal, right and left corner seals. Piece of cake. A five minute job.
Thanks
Thanks
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Raymond from ansonia, CT
- Parts Used:
- WD12X10304
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Very, very easy. Took about 5 minutes. The end cap was on and working. And the repair company would charge $65 just to come out and look at it. It costs $9.00 to fix it. I am moving on to the refrigerator next. Very satisfied. Shipping is well worth the money. Ray D, Ansonia, CT
Old cap was already off and had string on it. Cut the string. Placed end cap over. Used needle nose pliers to open metal rail a little and put in new cap. Locked right in. That was easy. Thanks again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Judy from Salem, OR
- Parts Used:
- WD12X10284
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Replace rinse aid fill cap
Opened the package and screwed in the new rinse aid fill cap. No problems. It fit and works just fine.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Old Lyme, CT
- Parts Used:
- WD12X10327, WD12X10304
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
2 rollers and end caps were broken were broken
Pulled the basket out the appliance and took what was left of the roller off and replaced them and slid the basket back onto the slide channel into the appliance. Then snapped the end caps on. Almost too simple. Less money than it costs to have the service man ring your door bell.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- mark from Fleming Island, FL
- Parts Used:
- WD7X14
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Eyelet Assembly Broke
Took off the lower faceplates. Removed the old eyelet assemblies (one broken, one not) and replaced both with new ones. Very easy to repair.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Clint from Quakertown, PA
- Parts Used:
- WD16X10011, WD16X313, WD16X297, WD35X10346
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Soap dispenser door wouldn't close
Replaced all ordered parts.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Russell from Columbia, SC
- Parts Used:
- WD12X10284
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
threads broke on rinse aid fill cap
Replaced with a new rinse aid fill cap.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stephen from MARENGO, OH
- Parts Used:
- WD21X10261
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Dishwasher wouldn’t start
Took the screws out of the back of the doorl located the switch and replaced it put screws back in and it was fixed
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rebekah from NEW ORLEANS, LA
- Parts Used:
- WD21X10261
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
My dishwasher would not start.
I unscrewed the inside of the dishwasher door and clearly saw the old interlock switch. This dishwasher has two, but it was obvious that one switch worked and one didn't (one switched was permanently pressed in). I removed the old interlock switch. It was tricky to pull out and I felt like I was going to break it but after watching youtube videos, I was pretty sure you just have to pull hard. I easily put the new switch in, reattached the dishwasher door, and it works perfectly!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Elizabeth from Westfield, IN
- Parts Used:
- WD24X10018
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
dishwasher wouldn't drain all the way
Removed 4 screws, took off basket covering, put new part in one turn, then replaced covering. Plumber had come out, I watched what he did, he had to order part and come back. I asked how much he didn't know but said cheaper than buying a new dishwasher. When he left I started calling around about the little plastic part that I needed. Part was $15.50. They called and said it would be $110.00. Needless to say I called them out and ordered the part myself and put it in. Took me like 6 minutes and cost $21.69. I was so mad about this situation that I even got my service call money back that I had already paid.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michelle from Richardson, TX
- Parts Used:
- WD12X10327
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken Roller
I watched the video and did exactly what he did. I am a novice when it comes to repairs. I learn as I go. This repair went flawlessly. Ordering was quick and easy. The part arrived quickly. The repair took less time than expected. The part was what I needed and nothing else broke or went wrong when repairing the original problem. It was a 100% success.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Art from Grants Pass, OR
- Parts Used:
- WD7X14
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Appliance door would fall open and was heavy to close
I first removed four screws holding the two cover panels attached to the dishwasher front at the bottom. Next I removed the broken cable and put everything back together that had sprung apart when the cable broke. Then I inserted the two door springs ends into the cable slots. Next I pulled on the springs to create slack and attached the cable / eyelet assembly to the protruding tab on the dishwasher frame. After attaching both sides the door works perfectly.
Was this instruction helpful to you?
Thank you for voting!
Dishwasher leacking at faucet
I pulled back the spring loaded handle that holds the hoses on the faucet. removed the ceeper ring. This dishwasher has leaked from the day it was purchased. I replaced the 4 jaws, the spring and handle. The inner seal was diffrent than the one in the kit so I cleaned the old one and replaced it.I replaced the faucet adapter. It worked fine. Being on a well the water was hard on the old one.
Was this instruction helpful to you?
Thank you for voting!