GMC910E* General Electric Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Gary from New Ross, IN
- Parts Used:
- WD24X10018
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
washer would not wash or pump out
removed piston in filter and replaced. the check valve had come apart and was not sealing
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ken from Central Square, NY
- Parts Used:
- WD24X10018
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Rubber piston on check valve was almost completely gone. Water backed up finally to the point of overflowing on kitchen floor.
Simply followed the instructions for the part on the part page. One thing that helped taking out some screws was to remove a couple of the brackets that hold the heating element and move it slightly. I would suggest cleaning all of the gunk out of drains and clean all holes in the screens using a toothpick, etc. Be careful not to overtighten the nut for the next time you have to do this!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- james from ham lake, MN
- Parts Used:
- WD24X10018
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
did not pump out all the water before drying
looked up the model no. on partselect web site and they discribed several diagnoses for different problems.they gave a 19% probability for a bad valve and nut. i removed the cover and the nut valve and the valve looked pretty bad. i ordered a new part and delivery was very good.i replaced the part and that took care of my problem. i was very happy with the whole repair.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Clifford from Saint Louis,, MO
- Parts Used:
- WD28X265
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
multiple rust spots on the old rack
Original part no longer made. Substitute too small by a half an inch. Corrected the problem by removing the 4 corner wheels from the old rack and put them on the new one. Now, it fits and works perfectly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Valdis A. from Louisville, KY
- Parts Used:
- WD24X10018
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Pliers
Water on bottom of DW does not drain & Wet/dirty dishes
Followed previous directions which were easy. Hard on back trying to reach over door all the way to the back. My DW is over 15 yrs old and the plastic plug w/corroded and locked into place. Tried turning it by hand to no avail since the plug turning lips were worn off/or not long enought to grasp it with. Took a hammer and chisel to the lips and turned it about an inch counter clockwise (either way), then lifted it out prying it with a screwdriver. KEEP IN MIND THE THREADS ARE JUST FOR LOCKING IT IN PLACE AND THE PLUG CAN BE TURNED EITHER WAY. IT DOES NOT SCREW IN!! Cleaned it with DW40 and reassembled it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Leanne from Divide, MT
- Parts Used:
- WD12X10284
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The rinse aid fill cap was stripped.
I removed the old cap and put on the new cap.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Philip from Seattle, WA
- Parts Used:
- WD24X10018
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
Dishwasher wasn't draining
After some investigation on the internet and partselect.com, ordered and replaced the piston and nut assembly inside the back of the dishwasher and the problem was fixed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Denver, CO
- Parts Used:
- WD24X10018
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Socket set
Dishwasher won't drain
Removed back screen, screwed out old piece, and replaced. Easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Tustin, CA
- Parts Used:
- WD24X10018
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Pliers, Screw drivers
C1 and C2 Error Codes, then Leaking
Dishwasher kept displaying error code C1 (drain partly blocked) and occasionally C2 (Drain completely blocked). The drain was fine. Parts Select said symptom "not draining" needed a check valve. Installed that (old one was very worn), but that didn't help. I decided to take off the bottom panel and eyeball the situation. Discovered a leak from the drain valve. But I also discovered the reason for the error codes. The leak had rusted the actuator in the drain valve solenoid so that it couldn't move reliably. So when drain time came, the drain valve didn't open, resulting in a C1 or C2 error (the washer electronics thought the drain was blocked--and in a way it was. I got the replacement parts for the leaking drain valve and installed them. Hints: take a photo of the assembly before you take it apart. Getting the push on nut off was an ordeal, as some have said. I spend at least two hours getting it off. I hope you have secret tool X13 to make it faster. Hint #2: There is play in the drain valve shaft, so I held it toward me with a pair of pliers while I pushed the new push on nut all the way tight to hold the new rubber washer. Hint #3: I used plumber's grease on the washer and shaft to make installation easier. I found the two pairs of long-handled needle nose pliers very useful. Oh, I sanded the rust off the solenoid actuator and added a bit of WD-40 and now the error code problem (as well as the leak) is over.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Susan from Lincoln, NE
- Parts Used:
- WD24X10018
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers
Dishwasher wouldn't drain after washing cycle
We went to the Part Select site and described the problem and they recommended a new piston and nut assembly and even provided a video on the installation. The only difficulty was removing the old piston and nut assembly which was corroded and broke off during removal. Once it was out installing the new part was very easy. And best of all the dishwasher completely drains. We had an estimate of $150 for a repair house call which would probably have resulted in another house call to actually install the part. With Part Select we received the part the next day, spent only about $18 and fixed the dishwasher in 24 hours--what a great experience!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Om Prakash from Highlands Ranch, CO
- Parts Used:
- WD24X10018
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Pool of water at the bottom of the dishwasher after the cycle is complete
It is so easy and simple! Just removed the old part ( Piston and nut assembly), which is at the back of the dishwasher(inside, behind the spray arm and the heating coil) with bare hands. It needs a little push and turn , just like you removing a old stuck nut. One you remove the old nut assembly, replace it with new one. Just hand tightened is enough. Ran the dishwasher and voila...it works like a new one. No more water collection at the bottom! All it took is 10 mins + 12 dollar part + 7 dollar shipping.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Lawrenceville, GA
- Parts Used:
- WD24X10018
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Water laid in bottom of dishwasher and turned black after end of cycle
Remove grid at inside at very back. At center under grid is the valve, unscrew CCW, and replace with new valve. Replace grids.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jo from Herndon, VA
- Parts Used:
- WD24X10018
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Dishwasher would not drain.
I cleaned all the drains in the dishwasher and the drain in the garbage disposal that leads from the dishwasher. I also removed the piston and nut assembly and tried cleaning it but the dishwasher still did not drain. I was using a wet vac to empty the standing water after the cycle completed. I bought the new piston and nut assembly. It arrived in 24 hours. I unscrewed the 4 screws in the back of the dishwasher that held the screen that covered the assembly, used my hand to unscrew the piston and nut assembly, screwed in the new part and replaced the screen and 4 screws. It completely fixed the problem.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Bradenton, FL
- Parts Used:
- WD12X10284
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Dishes cloudy, spotting
Unscrew old stripped out one and put in new one ..wala!! Easy repair for this old lady...
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bradley from Cambridge, WI
- Parts Used:
- WD24X10018
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
clips that hold the spinning arm in place broke
whole assembly screws out, replacement was a breeze. I love this site. Parts came quick
Was this instruction helpful to you?
Thank you for voting!