GMC6340KW147 General Electric Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Gerald from BLUFFTON, SC
- Parts Used:
- WD35X21038, WD12X10327
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Had cracked roller
Snapped right in
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Columbus, OH
- Parts Used:
- WD12X10327
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
upper rack wheel broken
took off the end clip, pulled the old wheel off and unclipped the bracket from the rack, then clipped the new assembly on...Simple!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bill from NEWPORT NEWS, VA
- Parts Used:
- WD8X229
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers
Old door gasket had become hardened and would not seal properly.
Pulled the lower left side end of the old door gasket out of door gasket retaining slot and slowly and evenly continued to work my way around the door pulling the door gasket out of the retaining slot until I reached the end. I installed the new gasket into retaining the retaining slot beginning on lower left side and then slowly and evenly working my way around the door inserting the new gasket into the retaining slot. I was careful to make sure the two cutout portions of the new gasket's retaining edge were correctly positioned in the lower corners of the door.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- kenneth from ocean isle beach, NC
- Parts Used:
- WD19X10032
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
leaky dishwasher
remove water connection; shut off circuit breaker ; follow the suplied directions; reassemble washer . job done - leak gone. Wife happy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Norman, OK
- Parts Used:
- WD28X10103
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Replace Top Spray Arm
As suggested. Pull washer, remove screws from top and replace with new part. Very simple and easy if you follow steps furnished by this site.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gloria from Vian,, OK
- Parts Used:
- WD26X10013
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Wrench set
Pump and motor went out.
We ordered our motor and pump assembly. When it arrived we followed the instructions that came with it. We had no problem with the instructions. We found it to be really easy. I was very happy since this happened 4 days before Thanksgiving. Thanks for the easy instructions, my husband got my dishwasher repaired in plenty of time for our Thanksgiving family get together.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Glenda from NORMAN, OK
- Parts Used:
- WD12X10327
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Top rack of the dishwasher had broken rollers.
Installation was very easy! Rack works perfectly now. Only problem...bought four sets instead of 4 parts since the order form didn't say it included 4 in each pack.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Edward from GRAND BLANC, MI
- Parts Used:
- WD35X21038
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
NONE
UNPACKED WHEELS AND CLIP. USING NEEDLE NOSE PLIERS SQUEEZED WHEEL TIP TO INSERT IN WHEEL. REMOVED OLD WHEELS AND RETAINER BY HAND. INSTALLED NEW WHEELS INSTALLED AND NEW RETAINERS
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Loren from BROWNSTOWN, MI
- Parts Used:
- WD12X10327
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Axles had broken, leaving the tray falling down when pulled out too far.
Followed the very excellent instructions provided on website by Hotpoint/GE
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Elizabeth from Vacaville, CA
- Parts Used:
- WD12X271
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
lost 2 front wheels.
There was a video on the page as the part. Done in a flash. The axle was a little hard to get into the wheel so I soaked it in a little hot water and it whet in like a charm.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sheila from DEERFIELD, IL
- Parts Used:
- WD35X21038
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
One axle cracked and broke off; another wheel was had fallen off and was distorted when it hit the heating element.
Removed all 8 wheels and inserted the new one after inserting the axles into each wheel. Replacement wheels had a much better connection to the bottom rack and do not anticipate any problems in the future.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Frederick from LANSING, MI
- Parts Used:
- WD12X10327, WD12X10304
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
The upper rack rollers are made of plastic after 5 years the plastic became brittle and broke so the rack fell.
Watched the video and swapped out the parts when they came. One of the arms that one of the rollers attached to was rusted and swollen had to remove the plastic coating and sand in order to get a good roller fit. Went super easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from GEORGETOWN, TX
- Parts Used:
- WD12X10327
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Upper rollers were broken
Pulled out the top tray fully, popped off the end caps. Removed the tray and placed it on the cabinet top. Popped off the old rollers and snapped on the new rollers. Replaced the tray into the dishwasher, Popped the end caps back on and I was done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Phillip from Canton, GA
- Parts Used:
- WD26X10013
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers, Socket set, Wrench set
The pump shaft leaked
I used the pump/motor replacement kit. It was a very easy repair and the parts were a direct replacement with no modification necessary. I saved over $300.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Marie from Westchester, IL
- Parts Used:
- WD8X229
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Dishwasher was leaking when turned on
I removed the screws from inside door panel. Took door panel out. Noted the way the old gasket was placed, removed it and replaced with the new gasket. Replaced the door panel. Felt pretty proud of myself until I realized that the door lock wouldn't work when I was going to run it. I have now removed the door panel again and am trying to get the door lock lever to work.
Was this instruction helpful to you?
Thank you for voting!