GHSD511P00SB General Electric Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- David from Columbus, OH
- Parts Used:
- WD12X10327
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
upper rack wheel broken
took off the end clip, pulled the old wheel off and unclipped the bracket from the rack, then clipped the new assembly on...Simple!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Vineland, NJ
- Parts Used:
- WD18X214
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Water was leaking from under the dishwasher
I turned off the water supply to the dishwasher. Then took off the front panels and disconnected the water. I then unscrewed the dishwasher from the countertop, pulled it out luckily there was plenty of play in the wire, and drain hose. I turned it on its side and had to remove a couple clamps to free th piece that I was replacing. Once I got to it, it just unscrewed. I put the new one on and everything back together. It was easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Daniel from Sebastopol, CA
- Parts Used:
- WD12X10327
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Upper rack fell into lower rack breaking dishes
My GE dishwasher had a problem. The upper rack would fall into the lower rack when loaded breaking dishes! Turns out, the front rollers on the upper rack were broken so that the supports would just pull out. So, I found the parts on this website easily. I then took off the plastic plug on the support which is easy to do. There is a flange you bend towards the rear of the dishwasher to release the plug. Once released you have access to the rollers, which just snap off easily. The new ones snap on easily. Reverse the cap removal, and you are done!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from ANNAPOLIS, MD
- Parts Used:
- WD15X10014
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers
Leaking Solenoid valve
1.Shut off the electric! 2.Shut off the water Supply. 3.Removed the two lower front panels(Two bolts each) . 4.The Water supply Solenoid is located far left up front . 5. Unplug power connector clip to the solenoid. 6.remove the two mounting bolts . 7. Use pliers to compress the rubber hose clamp And slide down the hose . 8 some small amount of water maybe in the hose a pan maybe necessary under the solenoid. 9.Gently pull the rubber hose off the nozzle. Complete installation in reverse. May The Force Be With You!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Frank from WEST DEPTFORD, NJ
- Parts Used:
- WD08X10057
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Door gasket was old and leaking.
I watched the video instructions and it looked easy! The old gasket just pulled right off easily! Installation of the new gaskets was quick and easy!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jason from Redmond, WA
- Parts Used:
- WD12X271
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Lower dish rack was missing one of the front wheel.s
Super-easy and quick repair -- quality part snapped right into place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kenny from CARUTHERSVLLE, MO
- Parts Used:
- WD13X10003
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Dishwasher would go on and off during operation
Took screws out of door panel to get to the latch and replaced old latch with new one. Super easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Loren from BROWNSTOWN, MI
- Parts Used:
- WD12X10327
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Axles had broken, leaving the tray falling down when pulled out too far.
Followed the very excellent instructions provided on website by Hotpoint/GE
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Glenda from NORMAN, OK
- Parts Used:
- WD12X10327
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Top rack of the dishwasher had broken rollers.
Installation was very easy! Rack works perfectly now. Only problem...bought four sets instead of 4 parts since the order form didn't say it included 4 in each pack.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Edward from GRAND BLANC, MI
- Parts Used:
- WD35X21038
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
NONE
UNPACKED WHEELS AND CLIP. USING NEEDLE NOSE PLIERS SQUEEZED WHEEL TIP TO INSERT IN WHEEL. REMOVED OLD WHEELS AND RETAINER BY HAND. INSTALLED NEW WHEELS INSTALLED AND NEW RETAINERS
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Elizabeth from Vacaville, CA
- Parts Used:
- WD12X271
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
lost 2 front wheels.
There was a video on the page as the part. Done in a flash. The axle was a little hard to get into the wheel so I soaked it in a little hot water and it whet in like a charm.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- helmut from EAST KINGSTON, NH
- Parts Used:
- WD35X21038
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Lower wheels kept falling off
Installed new lower rack wheel kit
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Debra from Hooks Town, PA
- Parts Used:
- WD28X10103
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
upper spray would fall off
Without any specific directions with the part (which would had been nice. If it wasn't for my husband I wouldn't have known where to start.) I had to carfully pull the dishwasher out of the cabinet (it wasn't heavy) to unplug the power supply. Then we unscrewed 2 screws on the top and the upper arm connection came off. We replaced it with the new one, screwed it back on, reconnected the power supply and pushed the dishwasher back where it belonged. It worked out very well.
Also I want to say I am very happy with the length of time it took to get my part to me. (1 day) I was washing dishes it no time.
Thank You
Debbie Bradford
Hookstown, Pa.
Also I want to say I am very happy with the length of time it took to get my part to me. (1 day) I was washing dishes it no time.
Thank You
Debbie Bradford
Hookstown, Pa.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jon from Henderson, NV
- Parts Used:
- WD8X181
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers
Dishwasher was leaking
Had to remove entire lower unit from dishwasher but it is a tight fit between the pump inlet flange and the floor.The next problem was to get the E clip off of the valve shaft. I knew the E clip had to be a straight fit when put back on the shaft so I had to straighten out before putting it back on the shaft after putting the new seal on the shaft correctly.Put the solonoid back on and made sure the valve shaft turned freely. Next fun was getting the pump unit back in place. Not easy (clearance) but got-er done!
Was this instruction helpful to you?
Thank you for voting!
Water leak around the Drain Valve Shaft.
Ordered the Drain Valve Shaft Seal and Push On Nut to make repair. Removed dishwasher from counter. Removed motor/pump assembly from dishwasher. Removed drain celenoid from pump. Removed old push on nut and old drain valve seal. Installed new seal and push nut. Replaced everything in reverse order. Amazingly no water leaks after reinstallation. Seams to be working fine so far....fingers crossed. Hoping to get a few more years out of this dishwasher.
Thank You PartSelect.
Thank You PartSelect.
Was this instruction helpful to you?
Thank you for voting!