41230B119 General Electric Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Sandra from Eastpointe, MI
- Parts Used:
- WD28X31818
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Upper rack was rusting and falling apart
To remove the old upper rack, I needed to use a screw driver to snap out the plastic end stops. That took a little time, because my dishwasher is located in a corner of my counter/cabinets, making the stop on the right very difficult to get to. Once that was done, I just slid the old rack out, the new rack in and replaced the stoppers. I was very impressed with your service and received my order in less time than stated on my order form. Will definitely use you again and recommend you to others!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Clifford from Saint Louis,, MO
- Parts Used:
- WD28X265
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
multiple rust spots on the old rack
Original part no longer made. Substitute too small by a half an inch. Corrected the problem by removing the 4 corner wheels from the old rack and put them on the new one. Now, it fits and works perfectly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Linda from Tucson, AZ
- Parts Used:
- WD28X31818
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers
Hard to get end caps off -broke them
My dishwasher used this part # as a substitute for the original part, which i guess is no longer made. After reading the other customers' comments,I thought people were describing two very different experiences with the installation -- some just "popped the cap off the end," or "couldn't be easier." Others had so much difficulty getting the cap off that they broke the cap. I think people must be dealing with totally different kinds of plastic caps. When I started on mine, I couldn't find a way to just "pop" the cap off. It was made so that some small flexible stems or prongs that slid in when installed could not be slid back out. I used a pliers to twist, poke, tilt, bend, whatever I could do to get the plastic cap off the end. That wasn't working, so I tried to bend rims the metal track open, but found the metal was too thick or strong for me to bend it. So I had to twist and force the cap, and the piece that kept the cap on broke off. On one side of the rack it was broken so badly that it couldn't be put back on--kept falling off. Had to try to crimp the rims of the track inward to keep the cap on. It's very loose but it has stayed in for the most part. The cap on the other side cracked enough to get it out without completely breaking off a piece. It went back in better than the first side. Pretty frustrating! I suspect because I don't have the original part with replacement caps to slide in. ?????
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Leanne from Divide, MT
- Parts Used:
- WD12X10284
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The rinse aid fill cap was stripped.
I removed the old cap and put on the new cap.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- NEIL from BOYNTON BEACH, FL
- Parts Used:
- WD28X31818
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
rusted out upper rack needed replacement
using small flat head screwdriver popped off clips at end of runners --rolled in new rack-- inserted clips back into runners
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Bradenton, FL
- Parts Used:
- WD12X10284
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Dishes cloudy, spotting
Unscrew old stripped out one and put in new one ..wala!! Easy repair for this old lady...
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- lawrence from lexington, NC
- Parts Used:
- WD15X93
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers, Wrench set
Old valve had hairline crack and leaking
2 screws to remove valve, turn water off, detach water line, detach plastic water outlet line, and put the new one on, reattaching everything in reverse. Electrical hookup was just two wires to solenoid. Slipped them off and back on new valve solenoid. Some difficulty getting support screws back in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bill from Fort Myers, FL
- Parts Used:
- WD28X265
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Lower rack had rusted through in several areas.
Pulled out the old and rolled in the replacement. The easiest part of the repair was ordering from the PartSelect website and receiving it via FedEx Ground the next day. Thank you PartSelect. Even my husband could have been successful with this.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Laura from New York, NY
- Parts Used:
- WD28X265
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
missing silverware basket
part came in the mail and fit the missing space perfectly. no complaints. easy fix.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- FRANCIS from WINOOSKI, VT
- Parts Used:
- WD28X265
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Old Basket Broke
Ordered a new basket it was a little large as I ordered the wrong size. I just broke of the tabs that held it in and now its perfect and larger !!!! Simple and great service !!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Patricia from Loganville, GA
- Parts Used:
- WD28X265
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Bought a manufactured home
with a dishwasher. Someone had 'packed' the silverware basket and there wasn't one in my dishwasher! Ordered one from here, when it arrived, opened the box, opened the dishwasher and placed it in the correct place. Closed dishwasher - DONE!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- tway from columbia, MO
- Parts Used:
- WD28X265
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
replaced dishwasher rack
nothing to it. slid old one out, slid new one in. however, replacement was not the same model as the original.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Corvallis, OR
- Parts Used:
- WD12X10284
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
Old rinse aid fill cap broke off at base
I removed the broken stub of the old fill cap with a screw remover. This was the only part that wasn't easy. The new cap fit fine.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Djuna from El Paso, TX
- Parts Used:
- WD28X31818
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
Old Dishrack was rusted and wheels broken
The hardest part about this is removing the end caps. I had repaired the wheels a long time ago so I had some idea about how to do it. Bending the back of the end cap very slightly and twisting got them out. Then it was simply a matter of switching the racks, which came with its own wheels, and then putting the end caps back on.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joan from Gloucester, VA
- Parts Used:
- WD28X31818
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
upper dishwasher rack - wheels deteriating and breaking apart
The new rack was somewhat similiar, but the center section that had to be snapped on was different...no spinner on top...thank goodness for the little video on how to take the stoppers off and reinstall them...it worked...thank you for what you have provided the public and me!
Was this instruction helpful to you?
Thank you for voting!