GSD4060N10SS General Electric Dishwasher - Instructions

Pieces just snapped together. Simple an quick. Part select was wonderful in assisting.

i first order the corner baffles and put them in. no change at all, still leaked terribly. the old baffles looked pretty good so i kept them. i then ordered the door gasket and the insert. i removed the old one, put in the new, and still no change. i thought perhaps the machine hadn't been used at all because it was like brand new inside, and previously owned by 'a little old lady'. i decided to load it up and run it on a regular wash, and have done that three times now. it drips a very small amount on the left corner but i'm quite happy that it decreased so much. I think perhaps the seal might be setting with the heat of the cycle because each time a load goes through it get less and less drips from that corner. The first order was sent by ups and they couldn't find where i lived so i actually had to go pick them up, but the second order was sent fedex and they had no problem finding my home, and i was very pleased with how fast my order came.

Replaced the tray with a new one. Would have been no problem at all, if I had realized how the track end clip was supposed to go. I thought the release had to be pushed toward the lock, but it needs to be pushed away from it. This sounds confusing, but when you look at it, it may be more clear to you.

Replaced the solenoid assembly.

door gasket dried out due to not using the dishwasher very often and needed to be replaced. removed door, replaced gasket, and re-installed door.

Repair was really easy just like the repair video, but you have to lay on the floor. Unfortunately, the problem wasn't the solenoid, but the pump/motor assembly. Be sure to check the solenoid operation before replacing (making sure it is cycling). It might be the pump/motor assembly. Good luck!

Removed dish washer from cabinet area and snapped new clip into cable and hook into support.. The time that took the longest was to removed the screws to pull the unit out of the cabinet area.. Very easy fix...

Removed bottom panel unplugged wires removed two screws removed it then replaced it

Had to install a new door latch. The installation itself is really quite simple involving removing (separating) the inner door panel to access the latch assembly. The latch is removed by simple push through one slot with a screw driver and the new unit basically pops in through grooved slots. However, I did find it quite helpful to first (and during) review a YouTube video illustrating the replacement. Although it is largely a simple procedure, for the first-time "installer" there are still a few tricky nuances to be aware of.

I unscrewed the front of the door almost to the bottom hinges and removed the latch. Went on line and ordered a replacement. The replacement arrived in a couple days (yeh), was identical to the one I had removed. I could have used another hand but went ahead and replaced it myself. It worked perfectly and I screwed everything back in place. I'm a 73-year-old female, good at taking things apart but not always good at putting them back together but will try anything. Was elated that I could repair it and it actually worked. Great service from your company!

Troubleshot and found that the solenoid had burnt up locking the drain door in closed position. I ordered solenoid, Note: I only received the solenoid. I used the old bracket and springs along with the piston arm for the solenoid. I had to break it free from the old solenoid. Once I got everything cleaned up and put together it took me about 10 minutes to install the solenoid. I manually tested mine prior to wiring back up to ensure proper movement and then tested to ensure that the piston arm did not pop out of the solenoid base.

Unscrew old stripped out one and put in new one ..wala!! Easy repair for this old lady...

Removed the existing inner door by removing screws along the edge of the inside door. Had trouble removing the door latch but after lifting it on one side of the plastic door fitting, it eventually lifted out. I also had some trouble getting the spring loaded soap door back into the replacement inner door. After playing with it for awhile I realized that the soap door should be in the open position when putting the spring latch back on. The soap door won't close until you get the entire inner door mounted and back on. I also want to note the the inside vent in the upper part of the inner door needs to be removed from the old inner door and installed in the new one. I missed that at first and it allowed condensation to get inside the door which caused the dishwashers alarm to go off during the dry cycle. One last note that I initially decided not to replace the existing sound proofing material in the new door based on advice from a website that stated that I wouldn't notice the sound difference. That was definitely untrue. I had to disassemble the door, replace the sound proofing and then it sounded fine. Overall it was a little difficult to figure out but considering how inexpensive the replacement door was compared with a having a service repairman come out, it was worth the trouble.

I removed the old cap and put on the new cap.

go to google..replace ge dishwasher rack.. very clear way to pry tab with a quarter and rotate end cap.. remove/replace rack reverse install end cap