GSD4128X03BB General Electric Dishwasher - Instructions

The Solenoid black plastic had melted around the solenoid shaft. I unplugged the solenoid, removed 2 screws,then one C clip and pulled the the unit out. The new solenoid is difficult to install all together as the shaft it goes on holds it all together when both springs are installed - - so I installed in one piece, with the 2 screws, except for the white plastic thing, the C clip that holds it on the shaft, and one of the two springs - - these three items went on separately. I wanted to thank the help your expert gave, but I couldn't figure how to do that.

We knew roughly how we needed to put the cap on the rail, but our technique of simply forcing it in the end of the rail wasn't working. The trick is to bend the moveable part of the plastic cap inward while you're sliding it in, and it clicks right into place.

The location of the cap we were replacing was the upper back left, which made it a little tricky to reach back there and insert it, especially for a bigger guy like myself. We took the bottom rack out and my smaller wife was more easily able to lean in the dishwasher and reach back there to insert it.

Inserted wheels on socket and then into the dishwasher rack.

Removed old rack replaced with new one which was an exact duplicate. Mama's happy; everybody's happy.

First I opened the package and screwed the new dispenser cap into place.

installed part on inside end of rail. no tools needed. original part wouldn't stay on rail. finished in 2 minutes
wife happy

Removed the lower rack and installed new wheels with clips

The newly purchased wheels have a little different design and could be installed in a matter of few seconds.

First I turned power to dishwasher off at fuse box.then,removed inside panel inside dishwasher about six screws.examined the control switch assembly and removed two screws that hold it into place.carefully removed two wire housings.Then located the part no.and model no.on the control panel.ordered new part online.The new control panel assembly arrived the next day.Installed it right away.Our dishwasher works as good as new. Thanks

first I used a shop vac to clean any excess water left behind, removed the sump housing from the motor, removed the sump housing from the body of dishwasher, replaced the old housing for the new one and reversed my steps to remove old one,

Read directions. They were poorly drawn. Set them aside. Opened up unit on December 26th. I made careful observation of the wiring, two hoses, one metal bracket, the hose two clamps, and then proceeded. Instructions said 1 to 2 hours, to complete. Ha Ha, perhaps if you've done it before. It was actually really closer to four hours. When done, it worked perfectly. The best part, my wife said: "This was the best Christmas present ever!" That made my day! Dishes are clean again, just like new! Thank you: www.PartsSelect.com.

I had already removed the screws that hold the inner door piece in place when diagnosing the problem. I snapped the new controller in place, put the 3 or so screws back in that hold it to the door, and replugged the wire harness connections from the power and the Sequencer. I put the inner piece of the door in place and replaced those 5 or so screws and restored power from the breaker box. The dishwasher gave a solid beep while the clean light flashed continuously. No other buttons were responsive and pressing the reset button caused a beep but nothing else. I began to research and diagnose that problem which was leading me to the Sequencer when I realized there was a "rewiring" plug on the controller I replaced that was not on the new controller. The controller which is made by Torisan is a generic part used by many manufacturers. The "rewiring" plug which goes into slot CN5 on the controller circuit card, which has wires that comes out of it and go back into other slots in the plug, is used to get the get the correct "pinout" sequence for GE's use of this generic component. Although I could find no information on this, the continuous beep was telling me there was a wiring problem. I removed the plug from the old controller, put it in CN5 of the new controller and the dishwasher works like a charm.

Replaced lower rack with new. Upper rack removed front stoppers, removed old rack, slit new rack in and replaced stoppers. Total time about 15 mins.

Ordered the part online and replaced the hoses. Very easy...took maybe 20 minutes

Use screw driver for leveage, righty tighty, lefty loosie, easy as that, and thanks to Parts Select, ordered my part on Thursday by dinner time Friday had part, install no washing dishies by hand, Thanks guys

Brian Souza
Vacaville, CA