CRD2000D02WB General Electric Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Carrell from Cochranville, PA
- Parts Used:
- WD12X10304
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
rack slide end cap missing
installed part on inside end of rail. no tools needed. original part wouldn't stay on rail. finished in 2 minutes
wife happy
wife happy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Palatine, IL
- Parts Used:
- WD19X10032
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers, Wrench (Adjustable)
Leaking water pump
Disconnect water line and screws (2) holding dishwasher under cabinet, and clamp for wastewater line. Pulled dishwasher out, turned on its side, and removed pump. Disassembled pump per instructions (great instructions) and installed new parts. Reversed to reassemble and except for a loose clamp that leaked (I tightened) it went well. Just under 1 hour.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Merle from Boulder, CO
- Parts Used:
- WD08X10057
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Severe lwater leak around door
Removed door panel. Removed old door seal and cleaned seal recess. Installed new seal. Replaced door panel on door and ran a cycle to check for leaks. Readjusted door latch to correct small leak. Ran another leak test. Job complete and wife is happy!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Patricia from Clifton, NJ
- Parts Used:
- WD12X10284
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Dispenser cap would not stay in place because it had melted
First I opened the package and screwed the new dispenser cap into place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Felix A from Orlando, FL
- Parts Used:
- WD12X271
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Missing wheels
Inserted wheels on socket and then into the dishwasher rack.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Nelson from Oroville, CA
- Parts Used:
- WD28X31819
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Disrack was getting rusty
Removed old rack replaced with new one which was an exact duplicate. Mama's happy; everybody's happy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lawrence from ROLESVILLE, NC
- Parts Used:
- WD21X10261
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
dishwasher did not start
Took out interlock switch (two leads) and replaced with new one. As simple as that.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Asok from HELOTES, TX
- Parts Used:
- WD35X21038
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Three of the 8 wheels broke.
The newly purchased wheels have a little different design and could be installed in a matter of few seconds.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- sandra from colorado springs, CO
- Parts Used:
- WD18X213
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
the sump housing was worn out and leaked
first I used a shop vac to clean any excess water left behind, removed the sump housing from the motor, removed the sump housing from the body of dishwasher, replaced the old housing for the new one and reversed my steps to remove old one,
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tom from UPPR CHICHSTR, PA
- Parts Used:
- WD35X21038
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Wheel had melted and support cracked
Removed the lower rack and installed new wheels with clips
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Raymond from Oshkosh, WI
- Parts Used:
- WD26X10013
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Motor froze up on dishwasher
Removed dishwasher, took off motor, and ordered part. It was delivered in a timely fashion (3 days). Determined which directions to follow. Used screwdriver to hook up motor. Put dishwasher back into cabinet area, made sure there were no leaks before fastening the dishwasher in place. Took about 1/2 hour to complete process. Very satisfied.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Helen from Carol Stream, IL
- Parts Used:
- WD12X10284
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Rinse Aid Fill Cap melted because it landed next to the heating element because it wasn't screwed in
Simply screwed in new cap
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- THOMAS from LACONIA, NH
- Parts Used:
- WD26X10013
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
poor dish washing
Read directions. They were poorly drawn. Set them aside. Opened up unit on December 26th. I made careful observation of the wiring, two hoses, one metal bracket, the hose two clamps, and then proceeded. Instructions said 1 to 2 hours, to complete. Ha Ha, perhaps if you've done it before. It was actually really closer to four hours. When done, it worked perfectly. The best part, my wife said: "This was the best Christmas present ever!" That made my day! Dishes are clean again, just like new! Thank you: www.PartsSelect.com.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Colleyville, TX
- Parts Used:
- WD08X10057
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
Dishwasher leaked
Plumber had suggested trying a new gasket rather than replace the dishwasher. Ordered one and installed it. Cleaned door and installed gasket in about 30 minutes. So far it works great .... and ... cheaper than new dishwasher.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Wyckoff, NJ
- Parts Used:
- WD08X10057, WD08X10015
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Leaked at bottom while running
Removed seven screws that held the inside panel to door. removed inside panel to work area and cleaned. After carefully observing the position of the old gasket, it was easily removed and the new one but in its place. Replaced the door being careful toalign the handle before tightly securing all seven screws. Repair worked, no more leak.
Was this instruction helpful to you?
Thank you for voting!