41461119 General Electric Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Lawrence M from Pollock Pines, CA
- Parts Used:
- WD22X10008
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Spray arm not functioning properly
Very simple. By hand, I unscrewed the old spray arm and screwed in the new one. One brief hangup. The old spray arm was very hard to unscrew. Rather than seeming to force it, I called the PartsSelect 800 number and got advice. The tech reassured me that all I had to to was unscrew it and put in new one. So I applied more force and old one came out. A breeze.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- donald from fullerton, CA
- Parts Used:
- WD28X265
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Silverware basket was missing in the condo that we rented
I just plugged in the model number and a screen came up that showed all the part numbers that made up the model. picked out the parts that we needed and ordered it and within 2 day we had the new basket that we needed for our dish washer.
the service and ease was better that going to the appliance store and picking up the basket.
I was very happy the the service.
Donald Brown
the service and ease was better that going to the appliance store and picking up the basket.
I was very happy the the service.
Donald Brown
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Sheffield, MA
- Parts Used:
- WD8X219, WD24X10018
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers
water would not drain at end of cycle
Went to repair parts on troubleshooting and found check valve assembly to be most common problem. Went to parts diagram to locate assembly and found it somewhat confusing as to exact location. Ordered part(s) on percentage as the problem. Received part next day (great)! Pulled dishwasher out and found I did NOT need to do so to replace check valve which is replaced without having to remove dishwasher. The gasket replacement was not necessary as it seals sump area from bottom of dishwasher and not the valve as it appears on the parts diagram. It took about 2 minutes to replace valve itself and it was the cause of the problem.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- THOMAS from LACONIA, NH
- Parts Used:
- WD26X10013
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
poor dish washing
Read directions. They were poorly drawn. Set them aside. Opened up unit on December 26th. I made careful observation of the wiring, two hoses, one metal bracket, the hose two clamps, and then proceeded. Instructions said 1 to 2 hours, to complete. Ha Ha, perhaps if you've done it before. It was actually really closer to four hours. When done, it worked perfectly. The best part, my wife said: "This was the best Christmas present ever!" That made my day! Dishes are clean again, just like new! Thank you: www.PartsSelect.com.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- frederick from auburn, CA
- Parts Used:
- WD08X10016
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
water leak
stripped old gasket from around the door (easy part)
instructions said to remove two screws from the bottom of the door to allow you to fit the gasket around the bottom
this was not too easy as you cannot get see the inside of bottom end of the door
I ended up removing the other door screws and this allowed me to fit the gasket quite easily
one tip tape the door lock immediately after removing screws as the lock assembly is not attached to the door
final step was to make sure the gasket was seated all around as my first wash had a slight lead
by pushing on the door after the door was locked cured the problem
instructions said to remove two screws from the bottom of the door to allow you to fit the gasket around the bottom
this was not too easy as you cannot get see the inside of bottom end of the door
I ended up removing the other door screws and this allowed me to fit the gasket quite easily
one tip tape the door lock immediately after removing screws as the lock assembly is not attached to the door
final step was to make sure the gasket was seated all around as my first wash had a slight lead
by pushing on the door after the door was locked cured the problem
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Helen from Carol Stream, IL
- Parts Used:
- WD12X10284
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Rinse Aid Fill Cap melted because it landed next to the heating element because it wasn't screwed in
Simply screwed in new cap
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Raymond from Oshkosh, WI
- Parts Used:
- WD26X10013
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Motor froze up on dishwasher
Removed dishwasher, took off motor, and ordered part. It was delivered in a timely fashion (3 days). Determined which directions to follow. Used screwdriver to hook up motor. Put dishwasher back into cabinet area, made sure there were no leaks before fastening the dishwasher in place. Took about 1/2 hour to complete process. Very satisfied.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Yuma, AZ
- Parts Used:
- WD28X31819
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
wornout rack
I took out the old one and put the new one in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Hillsborough, NC
- Parts Used:
- WD28X31819
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Put lower rack in
Took old rack out put new rack
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Harry from SAINT LOUIS, MO
- Parts Used:
- WD12X10284
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
New home to me. Part lost
Put on a new cap.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Shelton, CT
- Parts Used:
- WD16X10011, WD16X313
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
detergent shaft and arm broken
pretty easy, take off 7 screws from inside door
only hard part was getting arm to click into lever through the door. if you practice with the parts outside the door they lock together really well :)
only hard part was getting arm to click into lever through the door. if you practice with the parts outside the door they lock together really well :)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Friendswood, TX
- Parts Used:
- WD12X271
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Rollers were missing from front of the rack
The new rollers snapped into place on the rack, by simply pushing them in. I was able to do it by hand, my wife could not do the same, so you might use some pliers.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- MARK from CAPE CORAL, FL
- Parts Used:
- WD28X31818, WD28X31819
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
rusted dishracks
very simple pull out the old and push in the new
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- john from nashville, TN
- Parts Used:
- WD26X10013
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers, Socket set
would not drain but washed fine
easiest way i found to do it was pull dishwashers out from under the cabnet... laided a pillow down in front of the door and turned it on the front side... the part was very easy to get to at this angle....could have done it in less then 5 minutes but took my time to double check everything to be safe....took a total of about 10 minutes..... very happy now no longer need to vacume out the old dish water left at the bottom of the dishwasher...... i think most anyone could do this very easy....
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Hector from Chicago, IL
- Parts Used:
- WD22X10008
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
broken extention sprayer
I twisted off the old one off and then screwed in the new one. Very easy to install no tools needed.
Was this instruction helpful to you?
Thank you for voting!