PDT825SSJ2SS General Electric Dishwasher - Instructions

Read up on part at manufacturers web page and installed replacement correctly.

-Disabled power.
-1/4” nut driver to take off kickplate.
-Unplug wires harness to door
-Dismount dishwasher from cabinets and pull out 4-6 inches
-uncouple spring pulley from door hinges.
-Open dishwasher door about 4 inches and pull out and up to remove
-Lay door down and remove 4 -T20 star bolts and two 1/4” bolts from door hinges(the door hinge has four bolts, but only remove one from each hinge that connects to the inner plastic door)
-remove vent cap and push up on interior plastic door casing to separate outer and inner door.
-Unbolt the soap dispenser module via 1/4” bolts and replace with new module. (be sure to line up module and gasket properly, installing 1/4inch bolts crossways, slowly tightening each bolt for a perfect seal).
-Reassemble the inner/outer doors and reattach to dishwasher in reverse order.
Be sure to plug the doors electric harness and kickplate.
-Plug the dishwasher back in and run it through a test.

I recently replaced the user interface, which took about 30 minutes. A week later replaced the soap dispenser module, which took 20 minutes. Disassembling the door was easier the second round.

I would read this project very easy for somebody with technical skills and easy with no prior skills

The repair is easy for most if you have basic skills.

1. Cycle your unit to make sure all the water in the tub is emptied. (Start a cycle then cancel it which forces it to empty)

2. Turn off the power at the circuit/fuse panel & also turn off your water supply going to the unit which is usually under the sink with your sink plumbing.

3. Have a few old towels handy, there will be a little water but nothing that requires a wet shop vac, etc.

4. Remove the bottom kickplate (should be a screw on each side of the front of unit)

5. Disconnect the power supply wiring to make removal easier.

6. Disconnect the water supply line (have a towel handy there will be a little water in the supply line)

7. Unscrew the mounts either at the top and/or sides of the washer depending on the install method into your cabinetry.

8. Carefully slide out the unit.

9. Carefully turn the unit on its side or upside down depending on your preference to work on the underside where the pump is located. Again have a towel or two handy there will be some water that leaks out from the tub even after forcing an empty cycle.

10. The circulation pump is easy to remove. First plug the power line, there is a clip to disengage to separate the plug. A small flat screwdriver will help.

11. If this is a first time being replaced it will probably have crimp style hose clamps on the two lines coming off the pump. Again a small screwdriver will help pry it apart. Throw these away your pump kit will have new hose clamps for installation.

12. Once these clamps are removed you can slip the hoses off and the pump will be free to remove from the unit.

13. Installation is easy. Make sure the rubber hoses seal completely around the unit before clamping. Pay attention to make sure its sealed evenly, your unit will leak water otherwise once its functioning again.

14. My recommendation is to reassemble, slide the unit back into your cabinetry and hook your power and water supply up. Before you screw the unit back into place and close up the bottom panel, start a quick cycle. Within that first minute when the unit is filling and starting the circulation pump you can watch underneath and make sure your circulation pump lines are sealed and not leaking. Once satisfied, you can then stop the unit and finish securing the unit with mounting screws and closing up the bottom kickplate panel.

Good luck! You can do this :)

My granddaughter's fian'ce actially replaced the pump.
He pulled the dishwasher out, tipped it over and quickly and easily replaced the pump.
I had already snapped the converter on to the pump so it was ready to hook up. I had read previous messages that this part had a converter.
After putting the washer back in place we set it on a light wash to test it.
It went very well.

Looked upm the problem it said door wasn.t closed so cause was the door latch. put in the new one no change so I bought a new dishwasher

The only directions that came with the new pump and filter, was how to replace the filter. I had to find a You Tube video to show me where the drain pump was located., and the way to get to it. I also had to figure out how the new pump was hooked up electrically, since the new pump did not work with the plug in on the machine.

Due to the almost zero clearance between the recirculating pump and the floor, getting the pan to line up and engage the tabs on the dishwasher frame can seem to be an impossible task. I did accomplish the task as instructed in the owners installation manual once.

However, I observed that the leak was just a drop at a time only on the deep clean mode where water recycling was in constant use during a long wash cycle. So, I recommend to slide the pan in the relative position without trying to engage the tabs and you will still accomplish the reason for the leak pan. Remember, the purpose of the Leak Pan is to protect your floor, so use it the easy way as I am.

I had to replace a docking port. Parts Select had the part, labeled as stainless, just as this survey indicates. Well folks, the part I received is 100% plastic. It it the correct part, just not stainless. Should it have been stainless due to a faulty plastic design? I don’t know.

I used Parts Select for the simple directions for installation. I was eventually linked to a YouTube video for a completely different docking port. Does my part slip on? Does it press in? I don’t know.

Needless to say, this has been a cheap but frustrating ordeal that is not yet over. Thanks for having the stainless, but really plastic, part and for having directions for some other part available.

Took out 2 screws that held machine in cabinet. Pulled out dishwasher about 4 inches. removed old latch and disconnected electric connection. Put in new latch, reconnected electric connection, replaced screws, pushed machine back in cabinet, replaced 2 screws that hold machine in place. Works like new!

Super easy repair, just removed the old latch and replaced it with the new one.

Replaced motherboard, parts select,very helpful in helping diagnose problem! Exchanged parts, credit account after returned parts. Great customer service All good stuff! They brought their A game for this diy-er...

I followed You-tube instructions, very clear but not easy.
The door had to be taken off the dishwasher and then disassembled into its two halves, front and back, in order to remove the old handle and install the new.

Needed GE Technician to install. Partselect.com had to send a second replacement rack because the first one was defective. When the second on arrived, IT TOO WAS DEFECTIVE. After the Tech tried to install the second replacement, he was forced to remove a part from the original rusted rack in order to get the 2nd replacement to even stay in the rails of the machine. Tech was great, but the Partselect.com parts were unusable as sent.