4071110 General Electric Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- David from BURKBURNETT, TX
- Parts Used:
- WD12X10206
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Rinse aid cap leaking
Opened the door on dishwasher and installed the rinse aid cap. Checked for leaks. None found
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Fitchburg, WI
- Parts Used:
- WD12X10304, WD35X20994
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
End Cap and Wheel axle were worn or broken
This repair was a snap. The parts, though not identical to the original, fit perfectly. I was able to snap both the Rack Slide Cap and the new wheel axle to the existing washer cage and the machine works great now.
Thanks for the quick delivery and great website!
Thanks for the quick delivery and great website!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- MarilynNegri from BLAIRSTOWN, NJ
- Parts Used:
- WD12X10206
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Lost cap to rinse aid disoenser
Just screwed it on.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Wayne from PALMER, MA
- Parts Used:
- WD35X20994
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Rollers and axles were worn out
Removed the stops at the end of the upper rack, removed the old rollers. Replaced with new rollers and installed the stops back in place. Very easy, finished in less than 15 minutes. Replacement rollers very much improved with design from the original rollers.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kathleen from LOUISVILLE, KY
- Parts Used:
- WD28X10384
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
dishrack was worn and causing chips on dishes
just slid the new rack into place
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michelle from Carlisle, PA
- Parts Used:
- WD12X10163
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Detergent cap would not stay closed
After removing the screws, the front of the dishwasher easily came off. I put 2 screws back in to hold the control panel in place. I did not want that to dangle while replacing the part. The part came off easily after removing the screws. Everything went together easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joe from Clinton township, MI
- Parts Used:
- WD13X10045, WR02X10585
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Door latch broke
took off eight philips screws on inside door panel which then exposed the broken actuator and missing spring. Replaced broken and lost parts and reset actuator in door then reinstalled inside door panel. Done and I'm happy not to have called service.
Joe
Joe
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Daniel from Maurice, LA
- Parts Used:
- WD22X10084, WD22X10047, WD22X10046, WD12X10109
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
dishes where not clean after washing
change the nozzles and filter
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Estelle from Queen Creek, AZ
- Parts Used:
- WD08X10018
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
We had a rip in our tub gasket.
I removed the old seal, cleaned behind it, and then put the new seal in. We saw a video on You Tube on how to do it. Partselect also sent instructions on a e mail with the order receipt. We enjoyed working with you guys. Your customer service representative was very nice and accurate in sending out the part. All went as she said it would. Thanks!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- KEVIN from MACKINAW, IL
- Parts Used:
- WD12X10163
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
The detergent dispenser latch was broken
The repair was easy. Removed all the screws from the inside door panel, approx. 11. Watch out for that last screw as there isn't anything else holding the outside panel, inside panel and control panel together other than those screws. I then unplugged the old dispenser backed out another 6 screws and replaced the old dispenser with the new one. Put it all back together within about a half hour.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Chester from North Las Vegas, NV
- Parts Used:
- WD28X10399
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
Top rack had the plastic coating coming off
Had to replace the top rack in the dishwasher. Removing the top rack was a tricky. Have to push the tab out not in on the stopper ends of the rack. Unscrew the bolts on the water sprayer. Need to slide the sprayer instead of unclipping it. Real easy to do once it is realized. Should have taken 30 minutes if I knew this in advance
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Edward from TUCKAHOE, NY
- Parts Used:
- WD15X10003
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Screw drivers
Difficult to install the mounting screws
Nut driver and philips screwdriver.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ronald from MIDDLETOWN, DE
- Parts Used:
- WD35X20994, WD12X10304, WD12X332
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Upper rack rollers were sloppy & would lock up with the sde track jumping off the wall rollers
and figured that was the problem. After a call to a delightful young lady in your service department We concluded that these rollers were the only thing available. Dejected I went back to my project with the intent of removing the wheels and grinding them down BUT 1st I gave it one more try and after some careful alined--Presto they rolled into the 2 tracks. I snapped the end caps on tracks--Problems solved--Please note: if these parts were taken off of my Bill Please Recharge them to me.THANK YOU ALL (IT WORKS LIKED A NEW WASHER) RON TUCKER 302 449-0342
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from ATLANTA, GA
- Parts Used:
- WD35X20994, WD12X10304, WD14X10009
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Door flopping down hard
I removed the anchor screws at the top of the dishwasher, and the screws holding the bottom kickplate in place. I pulled out the dishwasher 8-10 inches to expose the cables where the plastic hinge arm links are installed.
On mine, there is a steel cable with a hook crimped on the end. The hinge arm link doesn't slide out of this crimped hook easily as-is, the opening is too small. I removed the old link pieces by breaking them, but I couldn't get the new hinge arm links installed without filing the opening of the hook to accept them more easily.
The demo installation video doesn't show this spring-cable-hook-hinge link configuration, so it was a little more involved than I expected. I would have packed my metal file if I had known this would be an issue. I replaced both sides while I was in there, and the remaining good one was pretty brittle. I was glad I took the time to do both. I had to file both sides to install the new links.
The dishrack rollers were easy to install.
The rack slide end caps from the factory were difficult to remove and reinstall without some pliers and elbow grease. The replacement part was much easier to install.
On mine, there is a steel cable with a hook crimped on the end. The hinge arm link doesn't slide out of this crimped hook easily as-is, the opening is too small. I removed the old link pieces by breaking them, but I couldn't get the new hinge arm links installed without filing the opening of the hook to accept them more easily.
The demo installation video doesn't show this spring-cable-hook-hinge link configuration, so it was a little more involved than I expected. I would have packed my metal file if I had known this would be an issue. I replaced both sides while I was in there, and the remaining good one was pretty brittle. I was glad I took the time to do both. I had to file both sides to install the new links.
The dishrack rollers were easy to install.
The rack slide end caps from the factory were difficult to remove and reinstall without some pliers and elbow grease. The replacement part was much easier to install.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Everett from FREDERICKSBRG, VA
- Parts Used:
- WD15X10003
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers
No water in
Pulled washer out. Found water inlet valve in lower left. Shut off power and water. Replaced valve with new.
Was this instruction helpful to you?
Thank you for voting!