4070810 General Electric Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Elahe from SAN JOSE, CA
- Parts Used:
- WR01X10623, WD27X10219
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
Toe kick was misding
Screw on the part.
The one screw was too expensive and o thought when I ordered it the package said 2 screw for $14.99 but only came with one screw.
We found an screw that worked.
I suggest the toe kick to include the 2 screw to make the experience of DIY easier
The one screw was too expensive and o thought when I ordered it the package said 2 screw for $14.99 but only came with one screw.
We found an screw that worked.
I suggest the toe kick to include the 2 screw to make the experience of DIY easier
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JOHNNY from FORT WORTH, TX
- Parts Used:
- WR02X10585
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
frost build up
flapper then bought the spring
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- C. from Lexington, KY
- Parts Used:
- WD01X10175
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Would only drain intermittenly
Thought it might be check flapper valve on drain pump, so I replaced fairly easily, per instructions. When doing, I noticed the attached relay wires were not secure. When it was on the drain cycle one of the relay wires vibrated badly and loosened the connection enough to only work occasionaly. Would like to put new relay on the pump but they do not sell separately from the pump. (one assembly). I resecured connection and will wait till relay gives out and buy new assembly, but for now it's working perfectly!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Cindy from Davidson, NC
- Parts Used:
- WD12X10304
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
Cap had broken off the top rack, it kept sliding down
I just had to play around with it to attach the new cap without breaking it.....never did this before but eureka! it worked.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Daryll from Newville, PA
- Parts Used:
- WD12X10304
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers
The top drawer of the dishwasher would extend past the support rails.
The top right rail, facing the dishwasher, has a self lock tab. Using pliers, straighten the lock tab, insert the cap and then restore the lock tab to it's original position.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donald from Harrison, AR
- Parts Used:
- WD21X10247
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Unit would not turn on
Changed the main chip. the unit then started and continuously ran. Thought something was wrong with it. It is just a cycle of the dishwasher and when the pump quit running the dishwasher ran and operates. Saved me lots of money and time.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kenneth from Dublin, OH
- Parts Used:
- WD12X10163
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
Old soap dispensor latch would not hold
Turned off the power at the main box. Removed the six phillips screws and two bottom hex screws holding the front panel. Removed the two solenoid wires on the old dispenser (Label wire polarity). Removed the eight screws holding the old soap dispensor and took it out. Cleaned the area around the hole. Laid down a bead of silicon caulk around the hole edges. Placed the new dispenser in the hole and replaced the eight screws (do not over tighten). Replaced the two wires on the dispenser solenoid (check polarity). Replaced the front cover (Do not over tighten. Turned on the power and job complete.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dorothy from LAKE WALES, FL
- Parts Used:
- WD08X10059
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Bottom door seal had crumbled with age
Removed inside of door, slide bottom seal on and put inside door back on. Job done!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jack D from CLEBURNE, TX
- Parts Used:
- WD22X10047
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Heat shield on lower spray arm came loose and blocked spray arm from turning
Followed instructions on how-to video on website on how to remove and replace lower spray arm.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- M Anne from VIENNA, VA
- Parts Used:
- WD22X10047
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Our dishwasher lower arm had become clogged
HAHA! The easiest repair we have ever done! Took it out of the box, snapped the old arm loose, put the new arm in and -- the dishwasher works like new! Thank you!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- carla from valdosta, GA
- Parts Used:
- WD22X10047
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Food particles had started stopping up spray arm and get them out.
Pulled old spray arm off and snapped new one on. Less than 3 minutes and works great. Dishes are cleaner now.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- john from SOUTHPORT, NC
- Parts Used:
- WD12X10304
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
rack slide end cap broke
Slide it into the arm until you hear it snap
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michele from NEOLA, UT
- Parts Used:
- WD13X10066
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
its wasn't latching so the dishwasher wouldn't work unless i held the door in the whole time
I called your tech and she sent me a awesome video that made it so easy to fix on my own
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Alan from MECHANICSVLLE, VA
- Parts Used:
- WD28X10177
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Broken silverware basket
Pulled the old one out and placed the new one right into place
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stephen from Waterville, ME
- Parts Used:
- WD12X10304
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
PS259168 Replaced broken end cap on upper dish rack
No tools needed for this half-minute repair. Just bend the flexible plastic tab on the back of the end cap until it slips into the metal rail and the end cap snaps into place. Couldn't be easier or simpler!
Was this instruction helpful to you?
Thank you for voting!