GSD2100N00WW General Electric Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Eric from Summerville, SC
- Parts Used:
- WD21X10268
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
dishwasher not draining
Repair was really easy just like the repair video, but you have to lay on the floor. Unfortunately, the problem wasn't the solenoid, but the pump/motor assembly. Be sure to check the solenoid operation before replacing (making sure it is cycling). It might be the pump/motor assembly. Good luck!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JoAnn from Daytona Beach, FL
- Parts Used:
- WD21X10261
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Would Not Start
Put part in. Put the door cover on & turned on & it worked. Thanks for having the part. So far, so good.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William F from new castle, DE
- Parts Used:
- WD21X10268
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
not draning
Removed bottom panel unplugged wires removed two screws removed it then replaced it
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Deanna from Benton Harbor, MI
- Parts Used:
- WD22X10055
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Extendable tower broke
On the front ,lower side of sprayer arm removed the 1/4" screw and you have to stick your head inside and look on the backside of the spayed arm. Locate the plastic clip and gently pry a little just enough to loosen it off the rest of the way, be careful not to break off. It came right off I popped on the new one replaced screw and rain a load of dishes. Thanks for your help and great products for us do it yourselfers.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JAYANTI from KANSAS CITY, MO
- Parts Used:
- WD21X10268
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Socket set, Wrench set
Water does not Drain
After installing the part, ran the washer once more. The water still remains in the washer. Tried washing several times. The problem is still the same.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Doug from Chesapeake, VA
- Parts Used:
- WD12X10408, WD18X10039
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Dishwasher would not drain completely
Disconnected power at circuit breaker, removed lower spray arm, fine filter, inlet cover, and sump cap - manually drained water from inlet sump, then laid dishwasher on its side. Removed motor/pump housing, collection chamber, and associated hoses from inlet sump and extracted inlet sump from inside the dishwasher. Reversed process to install new inlet sump, paying careful attention to ensure a leak-free repair. The problem was damage to the part of the inlet sump that receives the feed from the fine filter - the inlet sump material had been damaged when I tried to clear some debris, resulting in a less than perfect seal when the motor/pump reversed and attempted to push water out of the dishwasher. New inlet sump, perfect seal, all the pressure is now pushing water out of the dishwasher during the drain cycle. PartSelect diagnostic app and parts diagrams were instrumental in being able to repair the dishwasher for less than $25.00 versus a service call costing hundreds. Thank you.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Harry from Croghan, NY
- Parts Used:
- WD16X10011, WD12X324
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Detergent cup cover could not be locked closed prior to washing the dishes.
I removed the plastic inner door liner, removed the timer assembly. Replaced both plastic parts, Detergent cup release arm and dispenser release timer lever. The most difficult part was reassembling the timer lever spring. Long nose pliers made it simple. Works like new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Howard A. from Little Elm, TX
- Parts Used:
- WD21X10261
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Dishwasher would not start
Took the back off/there were six phillips head screws. Took the protective cover off the Interlock Switches and found the problem. One of the buttons was jambed and would not move. I pulled the switch up and pulled the connecting wires. This took a little bit of doing as the connectors have been set for over 8 years. I used a pair of needle nose pliers. I reconnected the new switch and punched both switches and the washer started. It was an easy repair after that, putting everything back in reverse order.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- cliff from knoxville, TN
- Parts Used:
- WD13X10003
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Faulty Dishwasher Door Latch
Had to install a new door latch. The installation itself is really quite simple involving removing (separating) the inner door panel to access the latch assembly. The latch is removed by simple push through one slot with a screw driver and the new unit basically pops in through grooved slots. However, I did find it quite helpful to first (and during) review a YouTube video illustrating the replacement. Although it is largely a simple procedure, for the first-time "installer" there are still a few tricky nuances to be aware of.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Terrence from New Castle, DE
- Parts Used:
- WD21X10268
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
My dishwasher would not drain.
Troubleshot and found that the solenoid had burnt up locking the drain door in closed position. I ordered solenoid, Note: I only received the solenoid. I used the old bracket and springs along with the piston arm for the solenoid. I had to break it free from the old solenoid. Once I got everything cleaned up and put together it took me about 10 minutes to install the solenoid. I manually tested mine prior to wiring back up to ensure proper movement and then tested to ensure that the piston arm did not pop out of the solenoid base.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Betty from Flintstone, GA
- Parts Used:
- WD13X10003
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Door latch would not lock dishwasher door
I unscrewed the front of the door almost to the bottom hinges and removed the latch. Went on line and ordered a replacement. The replacement arrived in a couple days (yeh), was identical to the one I had removed. I could have used another hand but went ahead and replaced it myself. It worked perfectly and I screwed everything back in place. I'm a 73-year-old female, good at taking things apart but not always good at putting them back together but will try anything. Was elated that I could repair it and it actually worked. Great service from your company!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Wantage, NJ
- Parts Used:
- WD15X10014
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
dishwasher was not filling with water
very happy with the product and fast shipping. removed kick plate from dishwasher, inlet valve was on the front left bottom slid out dishwasher removed two screws and disconnected water line,and installed new inlet valve,very simple job if your somewhat handy,make sure you use thred sealant on water line when re installing
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kenneth R from Marcellus, MI
- Parts Used:
- WD15X10014
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
Fractured brass bezel on bottom of valve- Leaking
simply removed broken valve and replaced with new valve, easy peasy. shipping was GREAT, Overnight. all in all a easy fix.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- robert j from elpaso, TX
- Parts Used:
- WD21X10261, WD13X10003
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
dishwasher stopped working
knew the cause of problem ordered parts prompt delivery 16 yr grandson did the repair with little or no assistance
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- paul from petaluma, CA
- Parts Used:
- WD15X10014
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Wrench (Adjustable), Wrench set
water dripping near front left of dishwasher
look at neww part first then r&r
Was this instruction helpful to you?
Thank you for voting!