MSD2100V50WW General Electric Dishwasher - Instructions

The only trick was the endcaps, which were not intuitive. I followed the instructions in the following Youtube video , which direct the user to bend a tab at the rear of the endcap back away from the front using a quarter in order to allow the endcap to rotate out of position inwards into the interior of the dishwasher. The old racks then slid easily out of the dishwasher, the new ones equally easily slid in, and then the endcaps required the tab to be bent back to allow them to rotate back into position.

Replace both micro switches.

I Just Open Door And Put Fill Cap In And Turn That It

No tools needed for this half-minute repair. Just bend the flexible plastic tab on the back of the end cap until it slips into the metal rail and the end cap snaps into place. Couldn't be easier or simpler!

placed the end cap into location and forced it into place. Fixed -and we are all much happier!!

Water was leaking from under the GE dishwasher, but once we pulled it out, had apparently been going on for a little while. Turning the water off to the dishwasher made it stop, so it was happening even when the unit was not running, potentially indicating somewhere early in the path of the water to and into the machine.

Indeed, inspecting the water inlet vale showed a slow leak. Getting the replacement part was fine, and it fit the electrical, water inlet (existing 90-degree water inlet elbow), and water outlet connections just fine - but the original machine screws that held on the original water inlet valve did not work. It took a little research to figure out the new type of screw required, which was apparently a 10/16 Type AB, which seemed to be a less common type of sheet metal screw (with a point), as opposed to the original flat-ended machine screws. So, after ordering those separately (which were a bit expensive), it went together fine.

A note on the water inlet valve part just indicating the the threading on those parts has changed over time, so potentially ordering the screws to attach it might be worthwhile, would be good information to add about the water inlet valve.

Inspected the old gasket. Removed, cleaned, re-seated existing gasket. Tested and found smaller leaks. Purchased and installed new gasket. Majority of leaks stopped but some detergent still leaks. Unsure what the problem is with that but the main leaks have been fixed. Dishwasher is less than 5 years old. Thank You.

The most difficult part was removing the old wheels. The plastic coating on the rack had come off, leaving the metal exposed. The wheels had rusted on - that's why they wouldn't roll. Once we got them off with pliers, hammer, screwdriver and basically everything in the tool chest, we were home free. Installing the new wheels and axles was easy.

I could not pull it out to get the new one in so I used a dremmel. Then pressed in the new one.

Thanks for your help.

Put end cap in dishwasher with movable part toward the back of the dishwasher. The free end of the movable part should be oriented at the top of the end cap. Put the lower half of the end cap into the rail behind the indented metal area so the widest part of the end cap is just opposite the hole where it should snap into place. Push the movable arm towards the back of the dishwasher until it fits under the upper rail. Then move the top half of the end cap into place under the top of the rail.

Press endcap in place after ensuring the rack is in track

Just remove the lower basket from the machine and pull the old wheels off. Then snap on the new wheels on the pegs. The old style wheels snap in place without much force. The new wheels take much more force to install and lock onto the basket which keeps them from coming off when the basket is heavily loaded.

Opened package, removed cap and screwed it in place.

It was so easy-just popped the end peice in and it fit perfectly. I also ordered 2 knobs for my dryer which was only one year old, they were also so easy to put on.. I received my parts 2 days after I ordered and because of some problems with my computer had to talk to the operators and was very pleased and happy with their help and with the parts that I ordered. I wil always order my parts from Parts Select.

I measured the diameter of the working wheels from the existing ones, and located the parts I needed from the website. I order two packages, each containing the wheels and axles for the rack.
When delivered, I snapped the wheels onto the delivered axles. Then, I snapped the axels unto the bottom rack, at the correct place. I used a large pliers for leverage because the axel was a bit tight to just simply snap on.
The middle wheels are located just behind the front wheels, thereby offering support when the botton rack is pulled forward for loading. Likewise, they offer support when the rack is pushed back in place.