PDT750SMF7ES General Electric Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Howard from PORT TOWNSEND, WA
- Parts Used:
- WD35X20794
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Upper Spray Arm broke in half from hitting something in the upper rack.
Had to remove the rubber gasket on the new spray arm to install the device, as it was hard to push into the above slot that fits the arm..
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tina from SOUTH WEST CY, MO
- Parts Used:
- WD24X29378
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
I had a hole in the drain line of my dishwasher.
It was relatively easy to fix. I unscrewed the mounting screws from the cabinet, slide the dishwasher out to access the pump under the dishwasher, I did raise the dishwasher on the left side and steadied with a stool to make access to the pump fitting easier. Then I loosed both clamps at the ends of the hose ie. from the dishwasher pump and the connection to the sink drain line, pulled the clamp off of the end that connects to the pump and placed it on the new hose connection, I removed the old hose, connected the new one and tightened the drain line connections. I placed the hose in the hose holders on the side of the dishwasher slid the dishwasher back into place and secured it in place with the mounting screws.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from CROSSVILLE, TN
- Parts Used:
- WD13X10071, WD21X10490
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
Dishwasher won't start.
Nightmare!!! The Striker latch did not pop out with a screwdriver as it was supposed to. The whole dishwasher needs to be disconnected and pulled out, then front door removed and totally disassembled to remove the screw to replace the striker latch. lots of work to replace a striker latch. Bad design!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jesse from PYLESVILLE, MD
- Parts Used:
- WD15X22948
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Wrench (Adjustable)
Dishwasher was not spraying water
Water valve replacement was easy. Turned off water supply valve. Unscrewed water supply from valve on dishwasher, removed 2 water hoses , that feed top and bottom sprayer’s And reinstalled everything opposite of removal. 5min job
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- PeggyAnn from EAST DUBLIN, GA
- Parts Used:
- WD13X10071, WD21X10490
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
broken latch
My son did the repair, I ordered both latch and striker, only needed the latch...only took him a few minutes to remove the old and install the new and works just fine
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- BENJAMIN from ONALASKA, TX
- Parts Used:
- WD12X26146
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
3 Plastic rollers on bottom of dish basket came off and melted by the heating coil in dishwasher,
Simply pick the basket up to slide wheels onto axles and push in until they lock in place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from CASTLE ROCK, CO
- Parts Used:
- WD01X10569
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
The pulley cable had broken
Unscrew the upper and side holding screws. Move dishwasher part way out. I didn't need to disconnect the water or electric. Make sure the electricity is off. Remember your working around water. Take off the bottom plat removing two screws, Remove broken cable pulley and replace new. Buy two since your their you might want to replace both. Have fun! It's duck soup.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mike from WADSWORTH, OH
- Parts Used:
- WD49X24057
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Old filter had calcium deposits that would not come off with soaking and scrubbing. That restricted water flow.
Simply twist on the new part/filter.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kristin from CONROE, TX
- Parts Used:
- WD35X20794
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Upper spray arm broke off and melted on heating element
Popped old bracket off with screwdriver, with a then easy installation of the new part.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Benjamin from VIENNA, VA
- Parts Used:
- WD21X10519
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers
The dishwasher was filling normally, but was not heating the wash water nor heating the dishes for the final dry. Dishes were not being properly cleaned and were not at all dry after the cycle.
I replaced the flood switch following instructions shown in readily available YouTube videos. In short, you remove the coarse and fine filters, then take out the bracket holding in the flood switch and finally the switch itself. After replacing the switch, the dishwasher works normally again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donald from NASHVILLE, TN
- Parts Used:
- WD21X10490
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Dishwasher door sensor/ mother board
Replaced motherboard, parts select,very helpful in helping diagnose problem! Exchanged parts, credit account after returned parts. Great customer service All good stuff! They brought their A game for this diy-er...
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- janet from WILMINGTON, NC
- Parts Used:
- WD09X21321
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Pliers, Screw drivers, Socket set
Broken Dishwasher Door Handle
I followed You-tube instructions, very clear but not easy.
The door had to be taken off the dishwasher and then disassembled into its two halves, front and back, in order to remove the old handle and install the new.
The door had to be taken off the dishwasher and then disassembled into its two halves, front and back, in order to remove the old handle and install the new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Herminio from TOMS RIVER, NJ
- Parts Used:
- WD21X10490
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Socket set
Door 1witch stopped working
1. Turned off circuit breaker
2. Pulled out dishwasher
3. Disconnected switch and popped out switch
3. Popped in new switch and connected
4. Pushed dishwasher back into place
5. Turned on circuit breaker
6. Turned on dishwasher and it worked
2. Pulled out dishwasher
3. Disconnected switch and popped out switch
3. Popped in new switch and connected
4. Pushed dishwasher back into place
5. Turned on circuit breaker
6. Turned on dishwasher and it worked
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- jeff from FORT COLLINS, CO
- Parts Used:
- WD08X22095, WD01X31858, WD01X31858, WD01X31858
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers, Wrench (Adjustable)
leaking from somewhere around tub
the actual gasket tub seal was easy, 10 minutes. The trim tub gaskets were a pain because I had to uninstall the dishwasher (not plumbing or electrical) then pull it out from the cabinet, remove old trim and re-install. Re-leveled dishwasher, screwed into side of cabinets but it still leaks. Can't figure out where but after replacing all the trim and gaskets its very frustrating.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Edward from VENICE, FL
- Parts Used:
- WD21X10490
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Door would pop open after starting dishwasher numerous times before latching would catch.
Removed two latch screws and one electrical connection, Removed
two screws that hold D/W to countertop, pulled D/W out enough to remove the old latch, install new latch, push D/W back into place, rescrew to counter top and rescrew the two latch screws. This problem happened since new, had repairmen twice and they did nothing but move the dishwasher stating it needed alignment, never mentioned this easy repair....
two screws that hold D/W to countertop, pulled D/W out enough to remove the old latch, install new latch, push D/W back into place, rescrew to counter top and rescrew the two latch screws. This problem happened since new, had repairmen twice and they did nothing but move the dishwasher stating it needed alignment, never mentioned this easy repair....
Was this instruction helpful to you?
Thank you for voting!