PDT750SSF2SS General Electric Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Jason from WESTON, WV
- Parts Used:
- WD21X10519
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Dishwasher would not receive water when started
The service lady looked up possible trouble items and narrowed it down to the flood switch. Being the most likely cause, I ordered a new one. I removed both trays, the lower sprayer, and both screens. The flood switch has an electric plug on the bottom of it that just pulls off. Just as with other appliance repairs, I actually got the old flood switch to work again before trying the new one. I should have tried to free up the float before ordering the new one. But in case this happens again, I’ll just put the new one in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tina from SOUTH WEST CY, MO
- Parts Used:
- WD24X29378
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
I had a hole in the drain line of my dishwasher.
It was relatively easy to fix. I unscrewed the mounting screws from the cabinet, slide the dishwasher out to access the pump under the dishwasher, I did raise the dishwasher on the left side and steadied with a stool to make access to the pump fitting easier. Then I loosed both clamps at the ends of the hose ie. from the dishwasher pump and the connection to the sink drain line, pulled the clamp off of the end that connects to the pump and placed it on the new hose connection, I removed the old hose, connected the new one and tightened the drain line connections. I placed the hose in the hose holders on the side of the dishwasher slid the dishwasher back into place and secured it in place with the mounting screws.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- BENJAMIN from ONALASKA, TX
- Parts Used:
- WD12X26146
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
3 Plastic rollers on bottom of dish basket came off and melted by the heating coil in dishwasher,
Simply pick the basket up to slide wheels onto axles and push in until they lock in place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jesse from PYLESVILLE, MD
- Parts Used:
- WD15X22948
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Wrench (Adjustable)
Dishwasher was not spraying water
Water valve replacement was easy. Turned off water supply valve. Unscrewed water supply from valve on dishwasher, removed 2 water hoses , that feed top and bottom sprayer’s And reinstalled everything opposite of removal. 5min job
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- PeggyAnn from EAST DUBLIN, GA
- Parts Used:
- WD13X10071, WD21X10490
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
broken latch
My son did the repair, I ordered both latch and striker, only needed the latch...only took him a few minutes to remove the old and install the new and works just fine
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from CROSSVILLE, TN
- Parts Used:
- WD13X10071, WD21X10490
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
Dishwasher won't start.
Nightmare!!! The Striker latch did not pop out with a screwdriver as it was supposed to. The whole dishwasher needs to be disconnected and pulled out, then front door removed and totally disassembled to remove the screw to replace the striker latch. lots of work to replace a striker latch. Bad design!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from CASTLE ROCK, CO
- Parts Used:
- WD01X10569
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
The pulley cable had broken
Unscrew the upper and side holding screws. Move dishwasher part way out. I didn't need to disconnect the water or electric. Make sure the electricity is off. Remember your working around water. Take off the bottom plat removing two screws, Remove broken cable pulley and replace new. Buy two since your their you might want to replace both. Have fun! It's duck soup.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mike from WADSWORTH, OH
- Parts Used:
- WD49X24057
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Old filter had calcium deposits that would not come off with soaking and scrubbing. That restricted water flow.
Simply twist on the new part/filter.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Benjamin from VIENNA, VA
- Parts Used:
- WD21X10519
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers
The dishwasher was filling normally, but was not heating the wash water nor heating the dishes for the final dry. Dishes were not being properly cleaned and were not at all dry after the cycle.
I replaced the flood switch following instructions shown in readily available YouTube videos. In short, you remove the coarse and fine filters, then take out the bracket holding in the flood switch and finally the switch itself. After replacing the switch, the dishwasher works normally again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donald from NASHVILLE, TN
- Parts Used:
- WD21X10490
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Dishwasher door sensor/ mother board
Replaced motherboard, parts select,very helpful in helping diagnose problem! Exchanged parts, credit account after returned parts. Great customer service All good stuff! They brought their A game for this diy-er...
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- janet from WILMINGTON, NC
- Parts Used:
- WD09X21321
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Pliers, Screw drivers, Socket set
Broken Dishwasher Door Handle
I followed You-tube instructions, very clear but not easy.
The door had to be taken off the dishwasher and then disassembled into its two halves, front and back, in order to remove the old handle and install the new.
The door had to be taken off the dishwasher and then disassembled into its two halves, front and back, in order to remove the old handle and install the new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Herminio from TOMS RIVER, NJ
- Parts Used:
- WD21X10490
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Socket set
Door 1witch stopped working
1. Turned off circuit breaker
2. Pulled out dishwasher
3. Disconnected switch and popped out switch
3. Popped in new switch and connected
4. Pushed dishwasher back into place
5. Turned on circuit breaker
6. Turned on dishwasher and it worked
2. Pulled out dishwasher
3. Disconnected switch and popped out switch
3. Popped in new switch and connected
4. Pushed dishwasher back into place
5. Turned on circuit breaker
6. Turned on dishwasher and it worked
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Edward from VENICE, FL
- Parts Used:
- WD21X10490
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Door would pop open after starting dishwasher numerous times before latching would catch.
Removed two latch screws and one electrical connection, Removed
two screws that hold D/W to countertop, pulled D/W out enough to remove the old latch, install new latch, push D/W back into place, rescrew to counter top and rescrew the two latch screws. This problem happened since new, had repairmen twice and they did nothing but move the dishwasher stating it needed alignment, never mentioned this easy repair....
two screws that hold D/W to countertop, pulled D/W out enough to remove the old latch, install new latch, push D/W back into place, rescrew to counter top and rescrew the two latch screws. This problem happened since new, had repairmen twice and they did nothing but move the dishwasher stating it needed alignment, never mentioned this easy repair....
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mike from LAS VEGAS, NV
- Parts Used:
- WD21X10490
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Broken door latch and springs were not connected.
Looked up the replacement part on YouTube, watched a video and followed the instructions. Part ordered was the correct part and the video showed how to access for replacing. Watched a different video for hooking up the disconnected springs that allow the door to lower and close smoothly. Whole process for repairs was less than 30 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Patrick from BROOKFIELD, WI
- Parts Used:
- WD21X10490
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Dish washer would not turn on
took off 2 sheet metal on the bottom, lowered the dish washer, pulled it out enought to unscrew 2 screws, unplugged the old part plugged in the new, put it back together.
Works like a champ.
Works like a champ.
Was this instruction helpful to you?
Thank you for voting!