GDT625PSJ0SS General Electric Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Sandra from JACKSONVILLE, FL
- Parts Used:
- WD21X31902C
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
Dishwasher not coming on
Make sure power to dishwasher is off. Unscrew from counter. Pull dishwasher out enough to expose pulleys that hold the door in place. Remove lower panel and insulation. Unplug door jack from main panel underneath. Loosen pulleys on each side and remove door. Take a 1/4 in socket and remove the bolt on the upper side of the hook on each side, then remove the screws on the outer side panel on each side. Now slide the inner door panel up (push the top and pull the bottom), which will release the hooks on each side. Turn over the inner panel and remove the four screws that hold the interface control panel in place. Unplug the two jacks and remove the panel. Now take a small flat-head screwdriver to remove the clear cover. Remove the control panel. Make sure you set the junction as prescribed with the instructions that come with the new control panel. MIND YOU- YOU HAVE TO REMOVE THE JUNCTIONS (TAKE EACH ONE OUT) AND RESET THEM ON THE PRONGS IN THE ORDER AS PRESCRIBED. Replace the control panel, replace the clear cover, insert it back in place, plug in jacks and replace screws. Turn inner panel over and line up side where the hooks lock. replace all screws and bolts. Replace door on dishwasher, plug in jack to main panel, attach pulleys to door. Replace insulation and front panel to bottom of dishwasher. Push dishwasher back in place. Replace screws that hold dishwasher to counter. Turn main power back on and VOILA!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gregory from EXPORT, PA
- Parts Used:
- WD08X21894
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
Old corroded gasket
Replaced gasket with a new one before further problems occurred. Got to get it in but it was relatively easy to place and snap in just make sure it fits on the right place where gasket inside meets ridges on door so it will be on properly for proper fit.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steve from Park Hill, OK
- Parts Used:
- WD22X33499
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Large hole in spray arm
Popped the old one off. Popped the new one on. Easy as that.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mason from JESSIEVILLE, AR
- Parts Used:
- WD22X33499
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Lower spray arm locking lugs had worn and it would pop off when the dishwasher was in use. It fell on the heating element during the dry cycle and a hole was melted through it.
I took out the old one and simply inserted the replacement. It was an exact replacement part and thus a perfect fit. Dishwasher is working fine now! Cost was around $40 (shipped) which I thought was reasonable.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from CASTLE ROCK, CO
- Parts Used:
- WD01X10569
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
The pulley cable had broken
Unscrew the upper and side holding screws. Move dishwasher part way out. I didn't need to disconnect the water or electric. Make sure the electricity is off. Remember your working around water. Take off the bottom plat removing two screws, Remove broken cable pulley and replace new. Buy two since your their you might want to replace both. Have fun! It's duck soup.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mike from LAS VEGAS, NV
- Parts Used:
- WD21X10490
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Broken door latch and springs were not connected.
Looked up the replacement part on YouTube, watched a video and followed the instructions. Part ordered was the correct part and the video showed how to access for replacing. Watched a different video for hooking up the disconnected springs that allow the door to lower and close smoothly. Whole process for repairs was less than 30 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jake from SACRAMENTO, CA
- Parts Used:
- WD22X33499
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
The heating element on our dishwasher burned the lower spray arm, melting it in 2 pieces
Simply unscrewed the old damaged arm and screwed the new one on, took less than a minute
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ed from TRAVELERS RST, SC
- Parts Used:
- WD22X33499
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Lower spray arm had melted tips
A quick twist of the locking nut
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Edward from VENICE, FL
- Parts Used:
- WD21X10490
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Door would pop open after starting dishwasher numerous times before latching would catch.
Removed two latch screws and one electrical connection, Removed
two screws that hold D/W to countertop, pulled D/W out enough to remove the old latch, install new latch, push D/W back into place, rescrew to counter top and rescrew the two latch screws. This problem happened since new, had repairmen twice and they did nothing but move the dishwasher stating it needed alignment, never mentioned this easy repair....
two screws that hold D/W to countertop, pulled D/W out enough to remove the old latch, install new latch, push D/W back into place, rescrew to counter top and rescrew the two latch screws. This problem happened since new, had repairmen twice and they did nothing but move the dishwasher stating it needed alignment, never mentioned this easy repair....
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ryan from Saint Joseph, IL
- Parts Used:
- WD15X26140
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers
No water in dishwasher
It took longer to uninstall and reinstall the dishwasher than it did to change out the part
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Maurice from SAN JOSE, CA
- Parts Used:
- WD12X32798
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Dispenser no longer opened during wash cycle
Very straight forward. After removing the power source the dishwasher was pulled forward enough to access the the door hinge springs. Then the door could be removed and the inner skin separated to access the the dispenser mounting screws.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Peter A from HOLLAND, MI
- Parts Used:
- WD28X28918
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Rubber Coating worn off rack...causing Plates to get rusty on their edges.
Open box...remove old rack from dishwasher...roll in NEW rack. Done!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- LaRay from PRESCOTT, AZ
- Parts Used:
- WD12X32798
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
soap did not dispense correctly
Followed video instructions step by step.
I was fortunate i had enough slack in water, electric and discharge lines to avoid disconnecting.
Two wrinkles
1. wire clips on my door had to be pulled/pried loose from door and there were two not one
2. could not slide dishwasher out after lowering adjusters and figured out it was the mounting tabs bumpimng the granite countertop, thus the use of putty knives to slide the dishwasher out.
I was fortunate i had enough slack in water, electric and discharge lines to avoid disconnecting.
Two wrinkles
1. wire clips on my door had to be pulled/pried loose from door and there were two not one
2. could not slide dishwasher out after lowering adjusters and figured out it was the mounting tabs bumpimng the granite countertop, thus the use of putty knives to slide the dishwasher out.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from CASEVILLE, MI
- Parts Used:
- WD21X10490
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Dishwasher would not sense door was latched
Super easy repair, just removed the old latch and replaced it with the new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from FLUSHING, MI
- Parts Used:
- WD22X33498
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Mid Spray Arm Assembly not spinning
The Mid Spray Arm Assembly was not spinning due to a dish that was in placed the dishwasher that was too high and hitting the arm. When it spun until it broke the center shaft. Replacement was easy. After removing power I pulled the upper tray out and removed the Conduit Mid Tiered Assembly by unsnapping it from the tray. I twisted off the broken spindle of the damaged arm assembly from the Conduit Mid Tiered Assembly and inserted the new arm and gently pushed it until it snapped into the Mid Tiered Assembly. Reinstalled the assembled parts by snapping into the tray making sure it was centered.
Was this instruction helpful to you?
Thank you for voting!