GDT530PGD4BB General Electric Dishwasher - Instructions

Simply put it on and twist it to lock in place. Took all of 3 seconds

Unplugged power.
Shut off water supply.
Remove the kick panel.
Unscrewed dishwasher from under cabinet and side screws. lower feet to reduce tension.
As you slide the dishwasher out, be sure all lines (Drain, water supply, electric are free to move with dishwasher.
I was able to hold the dishwasher at an angle to easily get to the valve. After removing the the valve, i screwed the new valve back into place. I removed the Line between the valve and Dishwasher. Putting the line on the new valve. I removed the water supply line from the old valve and installed it on the new valve.
Placed the dishwater back in place and screed it back in. I ran the cycles. everything works!
I replace the kickpaner a couple of hours later. Check to make sure there were now leaks.

Turned off pier at breaker. Removed dishwasher from under counter after disconnecting water line from dishwasher and drain tube from under sink. You might get a little residual water but not much. Removed old flood switch took about 2 minutes. Replaced with new flood switch. Then tilted dishwasher back to get to plastic nuts that hold down heating element. Set unit back down and removed old heating element then replace it with new one. Replace plastic nuts that hold element. Exact parts makes job easy. Them put water hose back on an put washer back in place hooked drain hose back up. Turned water and power back on. Tested unit worked perfectly. Hardest part of job was putting the dishwasher back into counter and getting the Instalation back on top.
Parts replacement time was about 10 minutes.
Disconnecting and reconnecting and replacing dishwasher 40 minutes. But I wouldn’t pay anyone to do this because it’s really not difficult.

Simple! I removed the flatware tray and pulled out the old rack assembly. Rolled in the new one and replaced the tray. Not really a "repair" per se but a needed replacement.

took out old and replaced with new

So after noticing some horrid food waste build up in my 9 year old dishwasher, I determined it wasn't heating the water during the wash cycle. I came on here to check how to replace the heating element and was surprised when the flood switch was instead strongly recommended as the first repair step.

I ordered the part, and prepped the dishwasher for the repair (Pro-tip: Clothes pin attached to the bottom of the flood switch wiring harness ensures it doesn't slip down below the opening during the part swap!). The part swap and reassembly only took 5-10 mins or so after prep and dishwasher is now heating water and running great again. Many thanks to partselect.com for the detailed installation guides/videos and the parts recommendations!

Repair was simple, lower rack just remove and replaced with out any tools or disassemble required, for the upper rack installation, the end cap need to be removed out of the sliding tracks, slide old rack out and discard, clean the track with a suitable cloth and slide new rack in to the tracks, reinstall the old end caps, as a good preventing measure, order new end caps just in case they are need it if the old ones crack during removal.
save old rollers from old racks for future repairs

My son did the repair, I ordered both latch and striker, only needed the latch...only took him a few minutes to remove the old and install the new and works just fine

Release DW from cabinet and pull out, Unplug power.
Remove kick plate and unplug door cable.
Open door about 6 inches and using socket back out 2 bolts at bottom of door corners.
Pull door up off hinges about 4 inches and slide old gasket out and install new gasket in place.
Reset door on hinges and reinstall bolts.
Plug door cable in and reattach kick plate and plug power cable in.
Push DW back in place and attach to cabinet and adjust kick plate

Simply pick the basket up to slide wheels onto axles and push in until they lock in place.

Simply twist on the new part/filter.

Popped the old one off. Popped the new one on. Easy as that.

I took out the old one and simply inserted the replacement. It was an exact replacement part and thus a perfect fit. Dishwasher is working fine now! Cost was around $40 (shipped) which I thought was reasonable.

Replaced gasket with a new one before further problems occurred. Got to get it in but it was relatively easy to place and snap in just make sure it fits on the right place where gasket inside meets ridges on door so it will be on properly for proper fit.

Unscrew the upper and side holding screws. Move dishwasher part way out. I didn't need to disconnect the water or electric. Make sure the electricity is off. Remember your working around water. Take off the bottom plat removing two screws, Remove broken cable pulley and replace new. Buy two since your their you might want to replace both. Have fun! It's duck soup.