GDT550HSD6SS General Electric Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Emilene from BRENTWOOD, CA
- Parts Used:
- WD28X20163
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Tine on lower rack broke
Just snapped it in place and that’s it!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Larry from STERLING, CO
- Parts Used:
- WD05X30818
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Dishwasher was not drying
I followed the U tube instructions already put out part select.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Cris from BAYFIELD, CO
- Parts Used:
- WD22X10094
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
The upper arm in the dishwasher broke.
Followed your instructions and was finished in 5 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Deborah from BRADENTON, FL
- Parts Used:
- WD21X10490
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Door would not shut, machine would not run.
Took out 2 screws that held machine in cabinet. Pulled out dishwasher about 4 inches. removed old latch and disconnected electric connection. Put in new latch, reconnected electric connection, replaced screws, pushed machine back in cabinet, replaced 2 screws that hold machine in place. Works like new!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from CASEVILLE, MI
- Parts Used:
- WD21X10490
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Dishwasher would not sense door was latched
Super easy repair, just removed the old latch and replaced it with the new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donald from NASHVILLE, TN
- Parts Used:
- WD21X10490
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Dishwasher door sensor/ mother board
Replaced motherboard, parts select,very helpful in helping diagnose problem! Exchanged parts, credit account after returned parts. Great customer service All good stuff! They brought their A game for this diy-er...
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ed from TRAVELERS RST, SC
- Parts Used:
- WD22X33499
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Lower spray arm had melted tips
A quick twist of the locking nut
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mark De from BRONX, NY
- Parts Used:
- WD22X33499
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Spray arm had become unattached and burned by the heat element
It was a simple as: attach and done!
There is a ring on the part that tightens clockwise to the nipple that sprays out the water that it rests on. Twist clockwise and you are done!
It is a mystery how it was unattached to begin with but not a problem in the end, it was easy to fix!
Thanks for sending genuine GE parts!
There is a ring on the part that tightens clockwise to the nipple that sprays out the water that it rests on. Twist clockwise and you are done!
It is a mystery how it was unattached to begin with but not a problem in the end, it was easy to fix!
Thanks for sending genuine GE parts!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from FLUSHING, MI
- Parts Used:
- WD22X33498
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Mid Spray Arm Assembly not spinning
The Mid Spray Arm Assembly was not spinning due to a dish that was in placed the dishwasher that was too high and hitting the arm. When it spun until it broke the center shaft. Replacement was easy. After removing power I pulled the upper tray out and removed the Conduit Mid Tiered Assembly by unsnapping it from the tray. I twisted off the broken spindle of the damaged arm assembly from the Conduit Mid Tiered Assembly and inserted the new arm and gently pushed it until it snapped into the Mid Tiered Assembly. Reinstalled the assembled parts by snapping into the tray making sure it was centered.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- janet from WILMINGTON, NC
- Parts Used:
- WD09X21321
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Pliers, Screw drivers, Socket set
Broken Dishwasher Door Handle
I followed You-tube instructions, very clear but not easy.
The door had to be taken off the dishwasher and then disassembled into its two halves, front and back, in order to remove the old handle and install the new.
The door had to be taken off the dishwasher and then disassembled into its two halves, front and back, in order to remove the old handle and install the new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from DANBURY, CT
- Parts Used:
- WD21X10519
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers
Ge Dishwasher was not filling with water
I replaced the Flood Switch Part Number: WD21X10519.
I found that be removing the bottom front cover under dishwasher door, there was a small black plastic clamp holding up the wiring cable. By disconnecting the clamp, it gave me a few more inching of wire inside the machine, which made disconnecting old flood switch easier. It also help in installing the new flood switch. Then finally i reinstall the clamp cable under the machine to finish the job.
I found that be removing the bottom front cover under dishwasher door, there was a small black plastic clamp holding up the wiring cable. By disconnecting the clamp, it gave me a few more inching of wire inside the machine, which made disconnecting old flood switch easier. It also help in installing the new flood switch. Then finally i reinstall the clamp cable under the machine to finish the job.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from CLIFFSIDE PK, NJ
- Parts Used:
- WD22X33498, WD22X10094
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Kept falling off during use.
Just took old one off & install new one. Snaps on dish rack. Took 5 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Nicholas from CONCORD, NH
- Parts Used:
- WD05X30818
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Wrench (Adjustable)
Dishwasher was not heating up to dry
Took out the old heating assembly and installed the new one
this did not solve my problem and I ended up buying a new dishwasher and returned the part
Spent as much in shipping to get the part and return it as the part cost itself
Next time I will just replace the dishwasher in the first place.
this did not solve my problem and I ended up buying a new dishwasher and returned the part
Spent as much in shipping to get the part and return it as the part cost itself
Next time I will just replace the dishwasher in the first place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Melissa from BELLPORT, NY
- Parts Used:
- WD22X10094
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Connector to sprayer broke
Connected sprayer aligned on bottom of top rack snapped in place. Very easy to install!
Was this instruction helpful to you?
Thank you for voting!