GDT580SMF8ES General Electric Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Earl from WINCHESTER, TN
- Parts Used:
- WD19X25187
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set, Wrench (Adjustable)
Water would not drain.
Unhook water line . Turn off power to dishwasher. Remove dishwasher from under counter. Lay it on its back. Loosen clamps on drain pump and remove pump. Install new drain pump and tighten clamps. Be sure to put hanger in the hole on the pump. Very easy job. Reinstall water line and put dishwasher back under counter. Turn on power to dishwasher. Go to go.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ivan from MANSFIELD, TX
- Parts Used:
- WD19X25187
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Dishwasher Not Draining
The pump went out after a few months of very loud noise during the drain cycle and then one day no drain or noise. A bit of research shows that this pump goes out frequently on this model so I ordered a new pump after inspecting the old pump for a clog or snag on the rotors.
The Install:
After removing the dishwasher from it's installed location and turning it on it's side (unplug water and electric of course), I was able to remove the pump from the two lines that connected it to the dishwasher and the drain line. I also had to unplug the pump from an electric connection to the dishwasher. Swapping out the new pump was the same but in reverse. Not a hard install, only simple tools required.
One note, my electric connection to the dish washer was different on this model pump since they changed the original part but there is an adapter included with this part so make sure it is in the box and fits before beginning.
The Install:
After removing the dishwasher from it's installed location and turning it on it's side (unplug water and electric of course), I was able to remove the pump from the two lines that connected it to the dishwasher and the drain line. I also had to unplug the pump from an electric connection to the dishwasher. Swapping out the new pump was the same but in reverse. Not a hard install, only simple tools required.
One note, my electric connection to the dish washer was different on this model pump since they changed the original part but there is an adapter included with this part so make sure it is in the box and fits before beginning.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Alvin from SCHENECTADY, NY
- Parts Used:
- WD05X30818, WD21X10519
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Nutdriver, Screw drivers, Socket set, Wrench (Adjustable)
No heat in both water and air
Followed troubleshooting procedure to determine that defective Flood Switch caused the problem and not the Heating Element. Replaced only the Flood Switch. I also replaced a deteriorated door gasket.
De-installed dishwasher from cabinet, removed door, and tipped unit over with back of tub resting on floor.
I followed the document referenced here for the troubleshooting and repair procedures: GE Appliances Technical Service Guide, 2012 GE Dishwasher, 31-9226.pdf available on web.
De-installed dishwasher from cabinet, removed door, and tipped unit over with back of tub resting on floor.
I followed the document referenced here for the troubleshooting and repair procedures: GE Appliances Technical Service Guide, 2012 GE Dishwasher, 31-9226.pdf available on web.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dennis from FORT SMITH, AR
- Parts Used:
- WD21X31910
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Screw drivers
Dishwasher would not turn on.
Watched YouTube video on how to diagnose problems. Once part was identified ordered from Partselect.com and replaced the user interface circuit board. Dishwasher is now working.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Aston, PA
- Parts Used:
- WD22X33499
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Water leak corners of door onto the floor
After hours looking for problem. I tried cleaning door gasket. Did not stop leak. Looked at lower water spray arm and it was split. It is literally a 2 minute repair to remove and install. Knock on wood, no leaks in the last 10 washes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from CASEVILLE, MI
- Parts Used:
- WD21X10490
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Dishwasher would not sense door was latched
Super easy repair, just removed the old latch and replaced it with the new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Daniel from CONCORD, NC
- Parts Used:
- WD21X10519
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Dishwasher wasn't heating water
So after noticing some horrid food waste build up in my 9 year old dishwasher, I determined it wasn't heating the water during the wash cycle. I came on here to check how to replace the heating element and was surprised when the flood switch was instead strongly recommended as the first repair step.
I ordered the part, and prepped the dishwasher for the repair (Pro-tip: Clothes pin attached to the bottom of the flood switch wiring harness ensures it doesn't slip down below the opening during the part swap!). The part swap and reassembly only took 5-10 mins or so after prep and dishwasher is now heating water and running great again. Many thanks to partselect.com for the detailed installation guides/videos and the parts recommendations!
I ordered the part, and prepped the dishwasher for the repair (Pro-tip: Clothes pin attached to the bottom of the flood switch wiring harness ensures it doesn't slip down below the opening during the part swap!). The part swap and reassembly only took 5-10 mins or so after prep and dishwasher is now heating water and running great again. Many thanks to partselect.com for the detailed installation guides/videos and the parts recommendations!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lonnie from YUKON, OK
- Parts Used:
- WD01X10569
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
REPLACE DOOR CABLE
Removed the top two screws that hold the dishwasher to the cabinet , remove the two screws on the bottom panel and remove the panel. Screw the levelers all of the way up and pull out the dishwasher about 6 to 8 inch. Hook the new cabe on the spring and pull around pulley and attach it to the door bracket. I replaced both cables. Reverse to complete.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- LaRay from PRESCOTT, AZ
- Parts Used:
- WD12X32798
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
soap did not dispense correctly
Followed video instructions step by step.
I was fortunate i had enough slack in water, electric and discharge lines to avoid disconnecting.
Two wrinkles
1. wire clips on my door had to be pulled/pried loose from door and there were two not one
2. could not slide dishwasher out after lowering adjusters and figured out it was the mounting tabs bumpimng the granite countertop, thus the use of putty knives to slide the dishwasher out.
I was fortunate i had enough slack in water, electric and discharge lines to avoid disconnecting.
Two wrinkles
1. wire clips on my door had to be pulled/pried loose from door and there were two not one
2. could not slide dishwasher out after lowering adjusters and figured out it was the mounting tabs bumpimng the granite countertop, thus the use of putty knives to slide the dishwasher out.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from FLUSHING, MI
- Parts Used:
- WD22X33498
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Mid Spray Arm Assembly not spinning
The Mid Spray Arm Assembly was not spinning due to a dish that was in placed the dishwasher that was too high and hitting the arm. When it spun until it broke the center shaft. Replacement was easy. After removing power I pulled the upper tray out and removed the Conduit Mid Tiered Assembly by unsnapping it from the tray. I twisted off the broken spindle of the damaged arm assembly from the Conduit Mid Tiered Assembly and inserted the new arm and gently pushed it until it snapped into the Mid Tiered Assembly. Reinstalled the assembled parts by snapping into the tray making sure it was centered.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stephanie from Huntsville, AL
- Parts Used:
- WD12X32798
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers
The soap dispenser was not opening during the washing cycle
Took off the door and separated the two door pieces. Unscrewed the old dispenser and replaced it with the new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph from KENNEDALE, TX
- Parts Used:
- WD22X33499
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Loud banging sound when dishwasher was on.
The base of the spray arm literally just spins a little bit into place like a luer lock. Takes two seconds to replace.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- GARY from SOAP LAKE, WA
- Parts Used:
- WD12X32798
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
The soap dispenser was broken os to save money I ordered one on-line
The repair instructions were great and the repair went well. The repair took less than an hour.
Thank you
Gary
Thank you
Gary
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Randal from TWIN FALLS, ID
- Parts Used:
- WD21X10519
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Socket set
Wife said Dishes were not Drying and leaving Spots !
I tested Heating Element with Ohm Meter-Direct Short (if open it would have been bad and I would need to replace the element. Per the Website Troubleshooting for GE dishwasher, it said Heating Element (65%), Float Switch (32%), or Computer Board (only 3% Chance of it being board). So I ordered Float Switch. Later I noticed that the dishwasher would not change wash cycles from Heavy, Normal or Light.
So I turned the Circuit Breaker on and off. This fixed the Wash Cycle.
When the Float Switch Came in, I installed it in a few minutes watching the video on the GE Troubleshooting Page. Later when it was running I checked the operation and when I opened the door, the wife says seeing the steaming water, You fixed it, the Water is Hot now ! It was all about Hot Water, not the Heating Element at all ! And I think everything was fixed when I flipped the Circuit Breaker on and off and re-set the computer board. I think replacing the Float Switch was good maintenance, cause it was really dirty and needed to be replaced soon anyway. And it may have avoided my wife's next misdiagnosis with our dishwasher. This was 2 weeks ago, and all is well.
Sincerely,
Scott
So I turned the Circuit Breaker on and off. This fixed the Wash Cycle.
When the Float Switch Came in, I installed it in a few minutes watching the video on the GE Troubleshooting Page. Later when it was running I checked the operation and when I opened the door, the wife says seeing the steaming water, You fixed it, the Water is Hot now ! It was all about Hot Water, not the Heating Element at all ! And I think everything was fixed when I flipped the Circuit Breaker on and off and re-set the computer board. I think replacing the Float Switch was good maintenance, cause it was really dirty and needed to be replaced soon anyway. And it may have avoided my wife's next misdiagnosis with our dishwasher. This was 2 weeks ago, and all is well.
Sincerely,
Scott
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kenneth from SEBRING, FL
- Parts Used:
- WD22X33498, WD22X33499
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
All 3 spray arms were stoped up.
Replaced all 3 spray arms in less than 10 minutes.The top one came in two pieces,the mounting bracket and the arm.Snap the bracket on the dishwasher first , then attach the arm to the bracket.
Was this instruction helpful to you?
Thank you for voting!