GDT580SGF2BB General Electric Dishwasher - Instructions

The Mid Spray Arm Assembly was not spinning due to a dish that was in placed the dishwasher that was too high and hitting the arm. When it spun until it broke the center shaft. Replacement was easy. After removing power I pulled the upper tray out and removed the Conduit Mid Tiered Assembly by unsnapping it from the tray. I twisted off the broken spindle of the damaged arm assembly from the Conduit Mid Tiered Assembly and inserted the new arm and gently pushed it until it snapped into the Mid Tiered Assembly. Reinstalled the assembled parts by snapping into the tray making sure it was centered.

Super easy repair, just removed the old latch and replaced it with the new one.

The base of the spray arm literally just spins a little bit into place like a luer lock. Takes two seconds to replace.

When new gasket arrived almost two weeks after it was sent out from Green Bay, I took out old gasket, marking which side was in and which out.
Then, with hands, fit new gasket in place making sure it was centered.
No leaking; it worked.
Thanks.

This is NOT a complaint about Parts Select (GE however has some packaging issues to resolve). It may become a complaint of Parts Select if not resolved to my full refund.

Unable to repair with provided part.

I have performed this repair in the past easily and successfully with part from GE Parts. GE Part Number: WD18X10052

GE Parts currently lists part number above as discontinued with a new GE Part
Number: WD35X10386. However not in stock

Found new part number locally however was missing the hose and plastic molded tubing that connects to pump and provides the actual diverter mechanism. Obviously did not purchase.

Ordered from Parts Select on 2021-12-22 and inquired if their part was complete. I was assured it was and paid for overnight shipping at approximate cost of $30.

Part arrives on Christmas Eve, a day late and incomplete. Called Part Select and was assured I would be reimbursed for full cost of part and shipping and was provided with shipping label to return incomplete part at their cost once their stock personnel verifies my claims.

I have photos of original/damaged but complete part beside new in package incomplete part for record and your use if you request.

Email Greg at:
One_US.Marine@yahoo.com

After hours looking for problem. I tried cleaning door gasket. Did not stop leak. Looked at lower water spray arm and it was split. It is literally a 2 minute repair to remove and install. Knock on wood, no leaks in the last 10 washes.

Researched what others have posted about on Parts select. That really helped with the diagnosis! Took a chance on a $28 part. Repairman was going to charge $150 just to show up, then diagnose, leave for 2 months while waiting for the part, charge another $150 plus the part to fix…
Just had to pull out dishwasher far enough to take the water supply line off. Then the water inlet solenoid then 2 more screws and a 2 pronged plug reattach water supply then done! 15 minutes MAX!!!

Bottom rack came complete with all racks. Only had to transfer the (2) side bumper guards,

My granddaughter's fian'ce actially replaced the pump.
He pulled the dishwasher out, tipped it over and quickly and easily replaced the pump.
I had already snapped the converter on to the pump so it was ready to hook up. I had read previous messages that this part had a converter.
After putting the washer back in place we set it on a light wash to test it.
It went very well.

Reviewed Control Panel replacement on line; found the OEM replacement parts on Part Select, began repair, found sea page of water, steam under door front causing slight corrosion on material of door; this allow moisture to seep through the plastic enclosure of the control board, causing it to malfunction; replaced components, due to "general" control board; Jumpers which did not exist on the original board, had to be configured; Parts Select fairly accurate, but when configured to diagram of repair document, "use Autosense" 570 jumper configuration; pin 1,4,8 jmpr'd; pin 2 Open; Control board did not work as required; no display, user could not select load size; luckily during the 2nd removal of the door, found manufacturer original paper work on the 580 model; to manufacturer recommended, Pin 1 Open, pin 2,4,8 jmpr'd; this configuration had the panel working as original; I also placed a light bead of clear silicon on metal panel as to assist in water transfer

I removed the old roller wheels and the new roller wheels snapped together and the simple instructions made the repair quick and simple..

I determined the guide rail on one side had broke when the white plastic bearings fell out of their track. I decided to replace both sides at the same time, so I ordered 2. They arrived quickly and I installed them and placed the middle rack back into the dishwasher. Went together fairly easily. I took pictures before removing the guides from the rack, so I would remember how to put the new ones back one when they arrived. Very happy with this DIY repair that easily would have taken much longer and would have been way more expensive! Thank you!

Had to trouble shoot to isolated the true fault condition. Checked heating element was good
Researched symptoms on YouTube
Removed and inspected float switch part
Ordered and replaced part.

I replaced the Flood Switch Part Number: WD21X10519.
I found that be removing the bottom front cover under dishwasher door, there was a small black plastic clamp holding up the wiring cable. By disconnecting the clamp, it gave me a few more inching of wire inside the machine, which made disconnecting old flood switch easier. It also help in installing the new flood switch. Then finally i reinstall the clamp cable under the machine to finish the job.

2 hose clamps, connect the wire with the wire adaptor suppled