GDT580SGF6WW General Electric Dishwasher - Instructions

Watched YouTube video on how to diagnose problems. Once part was identified ordered from Partselect.com and replaced the user interface circuit board. Dishwasher is now working.

The Mid Spray Arm Assembly was not spinning due to a dish that was in placed the dishwasher that was too high and hitting the arm. When it spun until it broke the center shaft. Replacement was easy. After removing power I pulled the upper tray out and removed the Conduit Mid Tiered Assembly by unsnapping it from the tray. I twisted off the broken spindle of the damaged arm assembly from the Conduit Mid Tiered Assembly and inserted the new arm and gently pushed it until it snapped into the Mid Tiered Assembly. Reinstalled the assembled parts by snapping into the tray making sure it was centered.

Followed video instructions step by step.
I was fortunate i had enough slack in water, electric and discharge lines to avoid disconnecting.

Two wrinkles
1. wire clips on my door had to be pulled/pried loose from door and there were two not one

2. could not slide dishwasher out after lowering adjusters and figured out it was the mounting tabs bumpimng the granite countertop, thus the use of putty knives to slide the dishwasher out.

Removed the top two screws that hold the dishwasher to the cabinet , remove the two screws on the bottom panel and remove the panel. Screw the levelers all of the way up and pull out the dishwasher about 6 to 8 inch. Hook the new cabe on the spring and pull around pulley and attach it to the door bracket. I replaced both cables. Reverse to complete.

Super easy repair, just removed the old latch and replaced it with the new one.

So after noticing some horrid food waste build up in my 9 year old dishwasher, I determined it wasn't heating the water during the wash cycle. I came on here to check how to replace the heating element and was surprised when the flood switch was instead strongly recommended as the first repair step.

I ordered the part, and prepped the dishwasher for the repair (Pro-tip: Clothes pin attached to the bottom of the flood switch wiring harness ensures it doesn't slip down below the opening during the part swap!). The part swap and reassembly only took 5-10 mins or so after prep and dishwasher is now heating water and running great again. Many thanks to partselect.com for the detailed installation guides/videos and the parts recommendations!

The base of the spray arm literally just spins a little bit into place like a luer lock. Takes two seconds to replace.

Took off the door and separated the two door pieces. Unscrewed the old dispenser and replaced it with the new one.

Had to trouble shoot to isolated the true fault condition. Checked heating element was good
Researched symptoms on YouTube
Removed and inspected float switch part
Ordered and replaced part.

I removed the old roller wheels and the new roller wheels snapped together and the simple instructions made the repair quick and simple..

I determined the guide rail on one side had broke when the white plastic bearings fell out of their track. I decided to replace both sides at the same time, so I ordered 2. They arrived quickly and I installed them and placed the middle rack back into the dishwasher. Went together fairly easily. I took pictures before removing the guides from the rack, so I would remember how to put the new ones back one when they arrived. Very happy with this DIY repair that easily would have taken much longer and would have been way more expensive! Thank you!

2 hose clamps, connect the wire with the wire adaptor suppled

I replaced the Flood Switch Part Number: WD21X10519.
I found that be removing the bottom front cover under dishwasher door, there was a small black plastic clamp holding up the wiring cable. By disconnecting the clamp, it gave me a few more inching of wire inside the machine, which made disconnecting old flood switch easier. It also help in installing the new flood switch. Then finally i reinstall the clamp cable under the machine to finish the job.

I followed the U tube instructions already put out part select.

I was very confident that the problem with my GE Adora DDT595SSJ5SS was that it needed a new UI board. It had been beeping randomly for a couple of months, requiring a circuit breaker reset every so often, until finally it stopped working entirely. When I looked at the main board underneath, the LED was flashing too fast for me to count the blinks. These were the signature signs of the UI board going out -- and this did indeed turn out to be the problem. I've run the dishwasher several times since replacing the board, and there have been no issues.

The only real issue I had with the repair job was removing the dishwasher door. This was because the door of my model was held in place by a pair of tension cables (bottom left and bottom right of the unit), rather than hinges, and the cable method of attachment is less documented online. I had to get hold of a user manual for my unit to even discover this fact about it, since I had purchased my home with this dishwasher already present and did not see it being installed originally.

What I had to do was to pull the unit out about five inches, exposing the attachments for these cables (they are on the outside of the unit), so I could hook my heavy wire hook under them and detach them. If your dishwasher has these cables on the door, you really do need a hook tool of some sort to remove them. If you have strong wire, you can make one yourself as I did. Anyway, removing the cables allowed me to remove the door. After that it was straightforward to unscrew and unbolt the various panels, set the jumpers on the new UI board, and screw everything back together.

I should note that the cables were not tricky in any way, just that all of these Adora units seem to be a bit different and I happened to have one with a method of attaching the door that is not very well documented. I hope that this helps someone with this type of unit. If you see those videos online referring to detaching the door from hinges, and you can't find anything on yours that looks or feels like that, consider that you might have cables instead on the outside of the unit.