GSD3360D50SS General Electric Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Robert from Hampton, GA
- Parts Used:
- WD14X10009
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Door had no resistance/no balance/would fall open
First, remove the bottom front covers (two parts four screws). Second, remove the two screws at the top that secure the dishwasher to the counter. Third, gently pull away the dishwasher from underneath the counter just far enough to see and be able to remove the door spring(s) - one on each side. Fourth, remove the existing hinge arm link(s) if not already broken off, replace with the new one(s). Note that the door hinge goes on the door (front) side of the spring and the other side fits into a groove on the door arm - the other end of the spring attaches to one of the 3 available holes on the frame at the bottom. It would be a good idea to replace the hinge arm links on both sides even if only one is broken. Make sure that the door has the right tension (each spring can be hooked in 1 of 3 holes to adjust the tension). Then gently push the dishwasher back under the counter. Finally, replace the screws under the counter and replace the covers on the bottom front. All of this should take no more than 15-20 minutes. This was an easy job!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Timothy from Chatham, NJ
- Parts Used:
- WD12X10304
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Discovered that the end caps were broken
Removed the broken items and clicked the new ones in place utilizing a pliers
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Christina from Claremore, OK
- Parts Used:
- WD12X10304
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The end cap broke off so when we would pull out the upper rack the whell would fall off of the track.
The end cap snapped into place perfectly without any problems and the rack works like new again. This is the second time I have used PartSelect.com and I am very satisfied with how fast I recieve the product and the easy of finding what I need. I would recommend them to anyone!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joyc e L. from Prosser, WA
- Parts Used:
- WD12X10304
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Rack kept coming off slider due to broken end
Popped in the part
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Denise from Fair Oaks Ranch, TX
- Parts Used:
- WD35X21038
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
bottom shelf would not roll properly
so easy! Ordered the rollers and clips ... popped them on and done!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- stephen from mashpee, MA
- Parts Used:
- WD35X21038
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
bottom basket of dishwasher kept following out
i needed new rollers and inserts to keep wheels on now its like new when i pull out bottom basket
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- R. Cecil from Norfolk, VA
- Parts Used:
- WD35X21038
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
wheel was distorted
Simply replace wheel
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tracy from Rockland, MA
- Parts Used:
- WD12X10304
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
the top part of the dishwasher down to bottom
first i see if i could move the metal piece it wouldn't move si i used a flat head screw drive to fix it . the end piece was to long so i cut a piece off it fitting it is not moving
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charlene from Nashville, TN
- Parts Used:
- WD12X10304
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Several
There is nothing to tell I order send to location and their maintenance installs
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Nick from Chatham, NJ
- Parts Used:
- WD35X21038
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
wheels colapsed
replaced new wheels
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dwight from College Station, TX
- Parts Used:
- WD31X10024
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
Front panel of the dishwasher was scratched badly!
I took the old front panel off which wasn't hard, and replaced with the new panel. The job would have been a lot easier if I had 2 hands, but it just took a little longer. Not much of a problem really! New panel looks great!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- George from Loving, NM
- Parts Used:
- WD26X10051
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers, Wrench set
Dishwasher pump was frozen
Ordered pump mechanism and replaced defective pump. A very easy replacement
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Nicholas from Alexandria, VA
- Parts Used:
- WD35X21038, WD35X21038
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
lost wheel
just snapped the new part in. couldn't have been easier
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- BRIAN from Keller, TX
- Parts Used:
- WD12X10304
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
SOmehow the upper rack end cap went missing. I needed to replace the cap so the rack would not pull all the way out and fall down.
I used needle nose pliers. I bent the stainless steel guide arm out so that I could insert the end cap. Once the end cap was installed I used the same needle nose pliers to "pinch" the guide arm back tight around the end cap. The end cap had premanufactured "notches" to hold the end cap in place once the guide arms are pinched down.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- George from Painesville, OH
- Parts Used:
- WD28X31819
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Plastic coating wore off the posts
Removed old dishrack. Inserted new dishrack.
Was this instruction helpful to you?
Thank you for voting!