GLDT696J00SS General Electric Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Carol from WALSENBURG, CO
- Parts Used:
- WD12X10231
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
two wheels broke off
knocked the broken piece off and snapped the new wheels on - easy breezy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jose from HOUSTON, TX
- Parts Used:
- WD12X10231
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers
Roller wheels on lower dish basket were worn and broken
Removed old roller with pilers and pop in New roller really easy very happy partselect had right rollers it made it easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- thomas from TINLEY PARK, IL
- Parts Used:
- WD12X10231
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Wheels broken
Just popped the old wheels off with small tack hammer very easy to get off and pop back on in a couple minutes..
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Adam from GRAND RAPIDS, MI
- Parts Used:
- WD28X10197, WD12X10231
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Original parts became brittle and broken.
Pulled original wheels and studs off. The snapped the new on to the lower rack. Swapped out the silverware basket. It was so easy women and children could do it! ;)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Fay from Highland, CA
- Parts Used:
- WD28X10197
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
Holes in middle silverware basket
Unsnapped the old middle basket, but then still having difficulty getting one side of the old basket to fit in the grooves on the new middle basket. Have tried it several ways, but still just does not seem to be the right fit on that one side.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Vivian from RAMSEY, NJ
- Parts Used:
- WD24X10048, WD01X10322
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Leaking drain hose
Removed leaking drain hose under the dishwasher from drain pump and sink drain pipe. Fed new hose behind dw connected with new clamps to dw drain pump and sink drain pipe. Put in high loop under sink.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Martha from Kingman, AZ
- Parts Used:
- WD12X10122
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Rinse Dispenser Cap melted on heating coil
Opened dishwasher after it completed a wash cycle. Found the rinse dispenser cap had come off during the wash and melted on the heating coil at the bottom of the machine. Pulled cap off of coil, made sure coil was not disturbed. Looked in various sites for cap. Finally found this site where I didn't need to order the whole mechanism and could order just the cap. Received the cap, screwed into the dispenser, fixed. The only problem I had was that there were two possible caps so I picked the one that was the same color as the original one. Project completed. Thanks
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- CRAIG from LEESBURG, VA
- Parts Used:
- WD12X10231, WD08X10063
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
Water leaking from dishwasher.
Competantly but it still leaks.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Calvin from Mankato, MN
- Parts Used:
- WD12X10122
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
aid cap melted
Twisted new one in place of old. Disappointed that there was a melting issue at all. Need to investigate problem.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Crown Agents USA from Washington, DC
- Parts Used:
- WD12X10231
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Wheels Had Fallen Off
The wheels on our bottom tray to our dishwasher had fallen off from a lot of use here in our office. When the wheels arrived, I just simply snapped them back on. A few had to be snapped on tight, but there were no tools necessary. Overall, a very easy fix.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- michael from center valley, PA
- Parts Used:
- WD08X10063
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
leaks out upper left hand corner
put new tub gasket on piece of cake
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Eric from Stephens City, VA
- Parts Used:
- WD12X10122
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Old rinse aid cap melted by heating element
Simply screwed in the new rinse aid cap to replace the old one
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Colette from Lakewood Ranch, FL
- Parts Used:
- WD12X10231
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The wheels were falling off from the bottom rack of my dishwasher.
I ordered 8 wheels, but I really needed just 4.( I am preventing for the future) It was so very simple to place my order and they were delivered in no time. I simply took off the old one, looked at how they were affixed and put the new ones the same way. Less than 2 minutes to do the entire job. I am a "Handy woman".
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- J from Johnson City, TN
- Parts Used:
- WD02X23651
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Wrench (Adjustable)
Rubber gasket for sealing top sprayer arm worn out
The repair piece containing the gasket must be unscrewed and the replacement piece is then screwed into place. Use of a wrench is necessary but used gentle compression as this piece is plastic. Also be careful when starting to thread the piece back on as too much pressure may push the part you are threading it onto out of the back of the dishwasher. ( Note that removing the top rack facilitates the job.. This is done by pushing the locks at the end of the roller tracks in and then to the side, opening the tracks for removal of the rack.)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Scott from Newark, OH
- Parts Used:
- WD12X10231
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Studs had become worn and needed replaced
Removed all wheels, then removed and installed new studs which were designed better than the origional and re-installed. Bottom rack now slides in and out much better.
Was this instruction helpful to you?
Thank you for voting!