GSD2200G20BB General Electric Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Joshua from Wylie, TX
- Parts Used:
- WD09X10024
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Lost the knob timer to the dishwasher, 2 year and 7 year old somehow made it dissappear - magic.....
Simpy went onto partselect.com and walked through getting the part, plugged it in after receiving in less than 2 days a voila - we are back in business
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Janice from Rockville, MO
- Parts Used:
- WD24X10014
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Couldn't drain water
I connected one end of hose to the drain using a hose clamp and screwdriver then connected the other end to the dishwasher using anouther hose clamp and a screwdriver..
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Victoria from Flower Mound, TX
- Parts Used:
- WD31X10024
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Toe kick not included
Removed screws and replaced the part. It couldn't of been earlier. Only problem this kit didn't include a toe kick and we are having a hard time finding it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Eric from Mayetta, KS
- Parts Used:
- WD21X10060
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Water not draining.
Removed the 4 screws on front inspection plate and had easy access to solenoid switch. Unplugged unit and switched out with repair kit. So easy a caveman could do it...
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rick from Rimersburg, PA
- Parts Used:
- WD21X10060
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Socket set
The dishwasher would not drain water out.
I removed 2 screws a wire plug connector and replaced the old part. The total repair including putting the cover plate back on only took about 15 minutes. Also I saved approximately $130.00 by doing this repair my self.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ben from florida, MI
- Parts Used:
- WD21X10060
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
dishwasher did'nt drain water . solinoid was melted and stuck
First I removed the two screws that hold the solinoid in place,then I removed the e clip and unpluged the wire and pulled out the plastic lever with the solinoid and springs. To install Solinoid:First I bolted on the bracket ,then I hooked in the spring in the plastic lever and installed lever on shaft then I hooked in the long spring to the bracket small hole in the bottum then I installed the e clip next I pluged in the wire.Then I tried the Washer .Averthing works fine.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- forrest from stuart, FL
- Parts Used:
- WD08X10057
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
replace door gasket
from the information previous customers had written.
it saved a lot of fustration and time
and best of all the dish washer does not leak.
it saved a lot of fustration and time
and best of all the dish washer does not leak.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Drums, PA
- Parts Used:
- WD21X33639
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Water Not Draining
Simply remove the kick plate locate the water drain selonoid. Took two screws out and one spring off.
So easy. Glad I did not hire a plumber.
So easy. Glad I did not hire a plumber.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- kevin from wellington, FL
- Parts Used:
- WD26X10013
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers, Wrench set
Dishwasher would not drain
Ordered motor and pump and replaced. Motor pump kit also comes with a drain solinoid so if that was the problem the kit repaired it. One issue is the size of the hanger to ensure the pump does not just hang on its mount. The directions were not very clear and after some trial and error I got it to work to.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Buddy from Danville, IL
- Parts Used:
- WD26X10013
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers
Pump seal was leaking
I disconnected the power shut off water supply. I then removed the drain hoses and water supply to the old pump. I removed the ground wire and the mounting rod to the old pump. Once removed, I followed the easy illustrated diagrams and instructions that came with the replacement pump.
I mounted the new pump using the supplied hardware and reconnected suply line and drain hose. I turned water supply and power back on. Ran a test cycle before reinserting under countertop. Amazingly quiet and no leaks. Repair a success.
I would use this service again if needed for additonal home appliances.
Thank you
Mr. Buddy King
I mounted the new pump using the supplied hardware and reconnected suply line and drain hose. I turned water supply and power back on. Ran a test cycle before reinserting under countertop. Amazingly quiet and no leaks. Repair a success.
I would use this service again if needed for additonal home appliances.
Thank you
Mr. Buddy King
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from EDGEWATER, FL
- Parts Used:
- WD21X33639
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
The timer was dead
Received the new timer in the late afternoon. Waited until the next morning to work on it. The biggest problem was taking the door apart. the time slid into a bracket and was held on with 2 screws and it's plug. This went like a piece of cake. The next problem was getting the door back on and together by myself.....but I managed it. The whole job took less than one hour.....and the dishes from the night before were given the test run!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Edward from TUCKAHOE, NY
- Parts Used:
- WD15X10003
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Screw drivers
Difficult to install the mounting screws
Nut driver and philips screwdriver.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Everett from FREDERICKSBRG, VA
- Parts Used:
- WD15X10003
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers
No water in
Pulled washer out. Found water inlet valve in lower left. Shut off power and water. Replaced valve with new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Brian from DERRY, PA
- Parts Used:
- WD15X10003
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Wrench (Adjustable), Wrench set
Leaking at the valve
Just like the video and replaced it
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roberto from Key Biscayne, FL
- Parts Used:
- WD21X10060
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers, Wrench (Adjustable)
Water would not drain out and keep filling up sprayers work
Your video doesn't include disconnecting water supply disconnecting electrical and disconnecting drain hose but after all that the repair to change the solenoid was a easy task but the problem was not solved so I TRIED . thanks Robert
Was this instruction helpful to you?
Thank you for voting!