GSC470M-01 General Electric Dishwasher - Instructions

I disconnected the power shut off water supply. I then removed the drain hoses and water supply to the old pump. I removed the ground wire and the mounting rod to the old pump. Once removed, I followed the easy illustrated diagrams and instructions that came with the replacement pump.
I mounted the new pump using the supplied hardware and reconnected suply line and drain hose. I turned water supply and power back on. Ran a test cycle before reinserting under countertop. Amazingly quiet and no leaks. Repair a success.

I would use this service again if needed for additonal home appliances.

Thank you
Mr. Buddy King

placed the end cap into location and forced it into place. Fixed -and we are all much happier!!

We just purchased a condo on the NJ shore, and the dishwasher had to be at least 50 years old. It was leaking, and my husband decided it needed a new gasket. I was surprised you still had pieces for this dishwasher in stock. It arrived and my husband replaced it and it is now not leaking. Thank you so much.

The top right rail, facing the dishwasher, has a self lock tab. Using pliers, straighten the lock tab, insert the cap and then restore the lock tab to it's original position.

No tools needed for this half-minute repair. Just bend the flexible plastic tab on the back of the end cap until it slips into the metal rail and the end cap snaps into place. Couldn't be easier or simpler!

This was one of those wonderful repairs where anything went right.
The part arrived overnight as ordered and even though I was abit leary of it fitting, since it was described as a replacement/new design, it fit perfectly! As mentioned in another post here, draining the water out of the unit so I could tip it over to do the replacement was the hardest part!
I'm sure I saved over $100 doing it myself. Thanks PartSelect!

I just had to play around with it to attach the new cap without breaking it.....never did this before but eureka! it worked.

repair kit was complete and directions were easy to follow. my model of dishwasher disnt even require any of the adapters. really only required removing a couple of clamps and replacing everything as a single unit

The replacement of the motor and pump assembly went smoothly and without difficulty however this did not fix the problem. It then appeared that the inlet water valve was not operating properly, so this part was ordered and instlled, a very simple proceedure that could be done witrhout removving fthe dishwasher from its cabinet. -- Again failure to run -- the timer assembly and electronic panel were then removed and examined. The control panel had no visible defects, so the timer assemblyand its cover was removed and examined . Uing a variable power supply the drive motor for the timer was energized and tested. As the motor ran properly the electrical switching contacts were then carfully checked, it was discovered that one contact set was heavily pitted and burned. These contacts were carefully cleaned and pollished with 1000 grit sanding paper. The actuator leaves were examined and two sets were found to be slightly out of alignment. The leaves on these sets were bent slightly to insure they were in line with the rest of the leaf serts. It was then noted that the rotating leaf('s) actuator had a home position indicated by a molded depression at one location and the motor was energized using approximately 5 volts ( a nine volt battery could also be used as a poer supply) observing prolper polarity to run the rotator until the home position was established and the actuator rods paul dropped into this depression. The assembly was then replaced in the diswasher using care to make sure that the actuation arm and spring were positioned properly weith the arrow end of the arm located in the recesss of of the rotating timer disk use care in placing the assembly and do not lose the sping which attaches to a mounting post and the arm. You may want to take a picture of the spring and arm locations when you rwmove the timer assembly to properly re-assemble all components, the repaired unit was placed back in its cabinet and a full cycle run to establish proper operation. And unit checked ok! Some of these proceedures are not for the weak of heart. I am a retired engineer who has been repairing my own equipment since graduation. .

A no brainer, replaced old fill cap with new fill cap. Delighted I was able to order the part, website is user friendly.

Put on a new cap.

Pulled out old basket with holes at bottom and replaced it with new basket. Perfect fit!

Opened the box the new silverware basket came in and replaced the broken one.m

Slide it into the arm until you hear it snap

Just follow the instructions and take your time. Clean out base trap and float control while you're in there.