GDF520PGJ2CC General Electric Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Robert from CASEVILLE, MI
- Parts Used:
- WD21X10490
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Dishwasher would not sense door was latched
Super easy repair, just removed the old latch and replaced it with the new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Brian from GRAND MARSH, WI
- Parts Used:
- WD08X23476
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Water was leaking at the bottom of the door
The old gasket pulled right out with no tools needed,
The new gasket went in the same way.
Results:
It did help on one side, but the bottom gasket also needs to be replaced it has a couple of tears one on each end.
Next Steps:
When the bottom gasket gets here I will replace that and it should be as good as new.
The new gasket went in the same way.
Results:
It did help on one side, but the bottom gasket also needs to be replaced it has a couple of tears one on each end.
Next Steps:
When the bottom gasket gets here I will replace that and it should be as good as new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Patrick from BROOKFIELD, WI
- Parts Used:
- WD21X10490
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Dish washer would not turn on
took off 2 sheet metal on the bottom, lowered the dish washer, pulled it out enought to unscrew 2 screws, unplugged the old part plugged in the new, put it back together.
Works like a champ.
Works like a champ.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Benjamin from VIENNA, VA
- Parts Used:
- WD21X10519
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers
The dishwasher was filling normally, but was not heating the wash water nor heating the dishes for the final dry. Dishes were not being properly cleaned and were not at all dry after the cycle.
I replaced the flood switch following instructions shown in readily available YouTube videos. In short, you remove the coarse and fine filters, then take out the bracket holding in the flood switch and finally the switch itself. After replacing the switch, the dishwasher works normally again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lynn from TOPEKA, KS
- Parts Used:
- WD28X28918
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Old tray was rusting.
Simply pulled the new one out of the box and put it into the dishwasher.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Peter A from HOLLAND, MI
- Parts Used:
- WD28X28918
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Rubber Coating worn off rack...causing Plates to get rusty on their edges.
Open box...remove old rack from dishwasher...roll in NEW rack. Done!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from FLUSHING, MI
- Parts Used:
- WD22X33498
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Mid Spray Arm Assembly not spinning
The Mid Spray Arm Assembly was not spinning due to a dish that was in placed the dishwasher that was too high and hitting the arm. When it spun until it broke the center shaft. Replacement was easy. After removing power I pulled the upper tray out and removed the Conduit Mid Tiered Assembly by unsnapping it from the tray. I twisted off the broken spindle of the damaged arm assembly from the Conduit Mid Tiered Assembly and inserted the new arm and gently pushed it until it snapped into the Mid Tiered Assembly. Reinstalled the assembled parts by snapping into the tray making sure it was centered.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Daniel from WATERBURY, CT
- Parts Used:
- WD28X22621, WD21X10519
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Dish washer wasn't getting the water hot to wash or dry
In did the drain screen, undid two nuts on top, removed panel, undid plastic ring, undid two screws with but driver, pulled sensor up, dried up any water at bottom, installed new sensor and follow steps in reverse. It worked!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph from KENNEDALE, TX
- Parts Used:
- WD22X33499
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Loud banging sound when dishwasher was on.
The base of the spray arm literally just spins a little bit into place like a luer lock. Takes two seconds to replace.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stephanie from Huntsville, AL
- Parts Used:
- WD12X32798
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers
The soap dispenser was not opening during the washing cycle
Took off the door and separated the two door pieces. Unscrewed the old dispenser and replaced it with the new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from CARY, NC
- Parts Used:
- WD21X10519
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Screw drivers
No boost in water temperature; water temperature during wash cycle not hot enough; dishes not drying
Had to trouble shoot to isolated the true fault condition. Checked heating element was good
Researched symptoms on YouTube
Removed and inspected float switch part
Ordered and replaced part.
Researched symptoms on YouTube
Removed and inspected float switch part
Ordered and replaced part.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Julian T from Dalton, GA
- Parts Used:
- WD01X35298
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
roller wheel was melted.
I removed the old roller wheels and the new roller wheels snapped together and the simple instructions made the repair quick and simple..
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from ST AUGUSTINE, FL
- Parts Used:
- WD21X10490
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
washer would nt ru it beeped 3x and flash start lite
Looked upm the problem it said door wasn.t closed so cause was the door latch. put in the new one no change so I bought a new dishwasher
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ed from Cassopolis, MI
- Parts Used:
- WD19X25187
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
would not drain water
2 hose clamps, connect the wire with the wire adaptor suppled
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dennis from JACKSON, MS
- Parts Used:
- WD21X31899
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers, Wrench (Adjustable)
Dishwasher wouldn't start.
YouTube search indicated the common problem was the Dishwasher Electronic Control Board, part # WD21X10537. YouTube was wrong. $83.76 mistake. (not Parts Selects fault)
I continued my search and stumbled on JustAnswers.com for $38.00.
They diagnosed the issue by me describing the lights that were blinking and for how long, and quickly told me the door latch is not registering. However, said it is rarely the door latch, but rather the Electronic Control Board, part # PS12726419 for $105.90. What the heck, I'll bite.
Bought both parts at Parts Select, quick shipping, solid packaging and good return policy (learned from previous experience). I did not return the 1st part, figured it probably wasn't long for this world anyway.
Dishwasher is running fine again. The combination of JustAnswers.com and PartSelect.com is far better than an extended warranty. Extended warranties last 3 yrs in most cases and cost as much as I spent. Someone with smaller hands could have done both repairs much quicker.
I continued my search and stumbled on JustAnswers.com for $38.00.
They diagnosed the issue by me describing the lights that were blinking and for how long, and quickly told me the door latch is not registering. However, said it is rarely the door latch, but rather the Electronic Control Board, part # PS12726419 for $105.90. What the heck, I'll bite.
Bought both parts at Parts Select, quick shipping, solid packaging and good return policy (learned from previous experience). I did not return the 1st part, figured it probably wasn't long for this world anyway.
Dishwasher is running fine again. The combination of JustAnswers.com and PartSelect.com is far better than an extended warranty. Extended warranties last 3 yrs in most cases and cost as much as I spent. Someone with smaller hands could have done both repairs much quicker.
Was this instruction helpful to you?
Thank you for voting!