GDF540HGD4WW General Electric Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- James from OMAHA, NE
- Parts Used:
- WD28X30219
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Upper rack rusted out
Took out the old and swapped out the parts from the old one and put them on the new rack. Looks great and works great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jake from SACRAMENTO, CA
- Parts Used:
- WD22X33499
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
The heating element on our dishwasher burned the lower spray arm, melting it in 2 pieces
Simply unscrewed the old damaged arm and screwed the new one on, took less than a minute
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jason from TULARE, CA
- Parts Used:
- WD12X32798
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Detergent module latch won’t close, latch broken
-Disabled power.
-1/4” nut driver to take off kickplate.
-Unplug wires harness to door
-Dismount dishwasher from cabinets and pull out 4-6 inches
-uncouple spring pulley from door hinges.
-Open dishwasher door about 4 inches and pull out and up to remove
-Lay door down and remove 4 -T20 star bolts and two 1/4” bolts from door hinges(the door hinge has four bolts, but only remove one from each hinge that connects to the inner plastic door)
-remove vent cap and push up on interior plastic door casing to separate outer and inner door.
-Unbolt the soap dispenser module via 1/4” bolts and replace with new module. (be sure to line up module and gasket properly, installing 1/4inch bolts crossways, slowly tightening each bolt for a perfect seal).
-Reassemble the inner/outer doors and reattach to dishwasher in reverse order.
Be sure to plug the doors electric harness and kickplate.
-Plug the dishwasher back in and run it through a test.
I recently replaced the user interface, which took about 30 minutes. A week later replaced the soap dispenser module, which took 20 minutes. Disassembling the door was easier the second round.
I would read this project very easy for somebody with technical skills and easy with no prior skills
-1/4” nut driver to take off kickplate.
-Unplug wires harness to door
-Dismount dishwasher from cabinets and pull out 4-6 inches
-uncouple spring pulley from door hinges.
-Open dishwasher door about 4 inches and pull out and up to remove
-Lay door down and remove 4 -T20 star bolts and two 1/4” bolts from door hinges(the door hinge has four bolts, but only remove one from each hinge that connects to the inner plastic door)
-remove vent cap and push up on interior plastic door casing to separate outer and inner door.
-Unbolt the soap dispenser module via 1/4” bolts and replace with new module. (be sure to line up module and gasket properly, installing 1/4inch bolts crossways, slowly tightening each bolt for a perfect seal).
-Reassemble the inner/outer doors and reattach to dishwasher in reverse order.
Be sure to plug the doors electric harness and kickplate.
-Plug the dishwasher back in and run it through a test.
I recently replaced the user interface, which took about 30 minutes. A week later replaced the soap dispenser module, which took 20 minutes. Disassembling the door was easier the second round.
I would read this project very easy for somebody with technical skills and easy with no prior skills
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Earl from WINCHESTER, TN
- Parts Used:
- WD19X25187
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set, Wrench (Adjustable)
Water would not drain.
Unhook water line . Turn off power to dishwasher. Remove dishwasher from under counter. Lay it on its back. Loosen clamps on drain pump and remove pump. Install new drain pump and tighten clamps. Be sure to put hanger in the hole on the pump. Very easy job. Reinstall water line and put dishwasher back under counter. Turn on power to dishwasher. Go to go.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ivan from MANSFIELD, TX
- Parts Used:
- WD19X25187
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Dishwasher Not Draining
The pump went out after a few months of very loud noise during the drain cycle and then one day no drain or noise. A bit of research shows that this pump goes out frequently on this model so I ordered a new pump after inspecting the old pump for a clog or snag on the rotors.
The Install:
After removing the dishwasher from it's installed location and turning it on it's side (unplug water and electric of course), I was able to remove the pump from the two lines that connected it to the dishwasher and the drain line. I also had to unplug the pump from an electric connection to the dishwasher. Swapping out the new pump was the same but in reverse. Not a hard install, only simple tools required.
One note, my electric connection to the dish washer was different on this model pump since they changed the original part but there is an adapter included with this part so make sure it is in the box and fits before beginning.
The Install:
After removing the dishwasher from it's installed location and turning it on it's side (unplug water and electric of course), I was able to remove the pump from the two lines that connected it to the dishwasher and the drain line. I also had to unplug the pump from an electric connection to the dishwasher. Swapping out the new pump was the same but in reverse. Not a hard install, only simple tools required.
One note, my electric connection to the dish washer was different on this model pump since they changed the original part but there is an adapter included with this part so make sure it is in the box and fits before beginning.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mary from KINGSVILLE, MO
- Parts Used:
- WD19X25187
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Drain pump quit draining
My granddaughter's fian'ce actially replaced the pump.
He pulled the dishwasher out, tipped it over and quickly and easily replaced the pump.
I had already snapped the converter on to the pump so it was ready to hook up. I had read previous messages that this part had a converter.
After putting the washer back in place we set it on a light wash to test it.
It went very well.
He pulled the dishwasher out, tipped it over and quickly and easily replaced the pump.
I had already snapped the converter on to the pump so it was ready to hook up. I had read previous messages that this part had a converter.
After putting the washer back in place we set it on a light wash to test it.
It went very well.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from ST AUGUSTINE, FL
- Parts Used:
- WD21X10490
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
washer would nt ru it beeped 3x and flash start lite
Looked upm the problem it said door wasn.t closed so cause was the door latch. put in the new one no change so I bought a new dishwasher
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Benjamin from VIENNA, VA
- Parts Used:
- WD21X10519
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers
The dishwasher was filling normally, but was not heating the wash water nor heating the dishes for the final dry. Dishes were not being properly cleaned and were not at all dry after the cycle.
I replaced the flood switch following instructions shown in readily available YouTube videos. In short, you remove the coarse and fine filters, then take out the bracket holding in the flood switch and finally the switch itself. After replacing the switch, the dishwasher works normally again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kim from BLACKFOOT, ID
- Parts Used:
- WD19X25187
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers, Wrench (Adjustable)
Drain pump needed replaced
The only directions that came with the new pump and filter, was how to replace the filter. I had to find a You Tube video to show me where the drain pump was located., and the way to get to it. I also had to figure out how the new pump was hooked up electrically, since the new pump did not work with the plug in on the machine.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph from KENNEDALE, TX
- Parts Used:
- WD22X33499
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Loud banging sound when dishwasher was on.
The base of the spray arm literally just spins a little bit into place like a luer lock. Takes two seconds to replace.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Teresa from DETROIT, MI
- Parts Used:
- WD21X10519
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Socket set
Dishwasher did not dry dishes
Followed directions on YouTube
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Erland from SAINT PAUL, MN
- Parts Used:
- WD28X20163
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Two tines broke off the original divider in the bottom rack
The part is held in with two plastic clips, which are easy to unclip. The part needed to be slightly flexed to release it and the new part went in the same way the old one came off. One issue: The replacement part had one extra row of tines that encroached on the silverware basket. As it turned out, one tine fit between basket sections and the other fit through the hole in the bottom of the basket and it doesn't interfere with utensils so it turned out not to be a problem.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Francesca from PALM COAST, FL
- Parts Used:
- WD28X30219
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Rusty upper rack
I simply followed the video instructions and replaced the rack myself, no tools required. Easy peasy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Emilene from BRENTWOOD, CA
- Parts Used:
- WD28X20163
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Tine on lower rack broke
Just snapped it in place and that’s it!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Larry from STERLING, CO
- Parts Used:
- WD05X30818
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Dishwasher was not drying
I followed the U tube instructions already put out part select.
Was this instruction helpful to you?
Thank you for voting!