GDF540HMF0ES General Electric Dishwasher - Instructions

I removed the old roller wheels and the new roller wheels snapped together and the simple instructions made the repair quick and simple..

Had to trouble shoot to isolated the true fault condition. Checked heating element was good
Researched symptoms on YouTube
Removed and inspected float switch part
Ordered and replaced part.

Board did not work. The socket for the jumper pins wasn’t installed on the board. Not sure if it was the correct unit. Decided to forget about doing a repair and just replaced the unit

I followed the U tube instructions already put out part select.

YouTube search indicated the common problem was the Dishwasher Electronic Control Board, part # WD21X10537. YouTube was wrong. $83.76 mistake. (not Parts Selects fault)
I continued my search and stumbled on JustAnswers.com for $38.00.
They diagnosed the issue by me describing the lights that were blinking and for how long, and quickly told me the door latch is not registering. However, said it is rarely the door latch, but rather the Electronic Control Board, part # PS12726419 for $105.90. What the heck, I'll bite.
Bought both parts at Parts Select, quick shipping, solid packaging and good return policy (learned from previous experience). I did not return the 1st part, figured it probably wasn't long for this world anyway.
Dishwasher is running fine again. The combination of JustAnswers.com and PartSelect.com is far better than an extended warranty. Extended warranties last 3 yrs in most cases and cost as much as I spent. Someone with smaller hands could have done both repairs much quicker.

Took out the old and swapped out the parts from the old one and put them on the new rack. Looks great and works great.

I replaced the Flood Switch Part Number: WD21X10519.
I found that be removing the bottom front cover under dishwasher door, there was a small black plastic clamp holding up the wiring cable. By disconnecting the clamp, it gave me a few more inching of wire inside the machine, which made disconnecting old flood switch easier. It also help in installing the new flood switch. Then finally i reinstall the clamp cable under the machine to finish the job.

The repair instructions were great and the repair went well. The repair took less than an hour.

Thank you
Gary

Followed the instructions on the video, it was pretty straight forward. It was helpful to know what to expect before hand like removing accumulated water in the drain before removing the flood switch so as not to have that water drain under the dishwasher. Knowing to have a nut driver with magnetic tip was helpful in removing and reinserting the screws. all in all it was pretty easy repair.

The part did not fit at all but not worth it to me to return it. The part I need is about 20 inches in length and the one sent was about 10 inches. I will simply call for this dishwasher to be repaired or replaced.

Followed directions on YouTube

My heating coil was not working so naturally I thought I needed a new coil and ordered one accordingly. During the time it took to ship to me, I did more research and people suggested testing the coil with and ohmmeter for resistance as often times the coil is fine and it is the flood switch that is the problem. I got an ohmmeter and checked the old coil and it returned readings that were just fine (btw 15-30), so I returned the coil and ordered this flood switch.

Anyone reading this debating between buying the coil and switch can save themselves a lot of trouble/time/money by removing the coil and testing it first.

The installation of the flood switch is fairly simple. There's a great video on Youtube for it (titled "GE Dishwasher not Drying Dishes - How to Replace Bad Flood Switch:), so I won't walk through the step-by-step on it.

However, one word of advice is to be careful when installing so that you don't let the o-ring on the switch slide down the connector/wire once you connect them or you'll get a slow leak into the catch pan at the bottom.

Also, if this if your first repair on a GE Dishwasher then get to know the unit while you have it pulled out. It won't be your last repair based on my experience...

So easy, even I was able to do it. Slide tabs back on defective basket and remove both sides, then slide the tabs onto new basket and place in dishwasher. All Done!

Parts diagram shows Striker can be popped out with screwdriver. Not true. It has a screw bolting it internally. Impossible to get to unless you disassemble the entire door. We took a power drill and small drill bit and bore it out like a cavity in a tooth. Needle nose pliers to extract the screw. Pretend your a dentist. Fixed it in 5 minutes. Replacement fit tight. A+

Installed new heater by pulling unit out of it’s cubby hole. Was able to gain access to the nuts that hold it down and make the seal, as well as the electrical connections. Re-installed. Helpful if you remove both dish baskets and utencil basket for access when installing heater.