GDF570SGF7CC General Electric Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Mason from JESSIEVILLE, AR
- Parts Used:
- WD22X33499
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Lower spray arm locking lugs had worn and it would pop off when the dishwasher was in use. It fell on the heating element during the dry cycle and a hole was melted through it.
I took out the old one and simply inserted the replacement. It was an exact replacement part and thus a perfect fit. Dishwasher is working fine now! Cost was around $40 (shipped) which I thought was reasonable.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kathleen from Vero Beach, FL
- Parts Used:
- WD28X28918
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
lower rack was getting rusted
Took out of box and slipped old one off and new one in. That easy and I am 83 years old. Took maybe 5 minutes to install.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jedrino from HAWTHORNE, CA
- Parts Used:
- WD22X33499
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Thumping Sound during the WashRinse cycles
Chances are your Lower spray arm is worn or jets are off. Replacing this part is very easy. Grab the base of the lower spray arm, twist and pull straight up. Place the new one in and twist lock in place. Repair complete!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kristin from CONROE, TX
- Parts Used:
- WD35X20794
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Upper spray arm broke off and melted on heating element
Popped old bracket off with screwdriver, with a then easy installation of the new part.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mike from LAS VEGAS, NV
- Parts Used:
- WD21X10490
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Broken door latch and springs were not connected.
Looked up the replacement part on YouTube, watched a video and followed the instructions. Part ordered was the correct part and the video showed how to access for replacing. Watched a different video for hooking up the disconnected springs that allow the door to lower and close smoothly. Whole process for repairs was less than 30 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Edward from VENICE, FL
- Parts Used:
- WD21X10490
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Door would pop open after starting dishwasher numerous times before latching would catch.
Removed two latch screws and one electrical connection, Removed
two screws that hold D/W to countertop, pulled D/W out enough to remove the old latch, install new latch, push D/W back into place, rescrew to counter top and rescrew the two latch screws. This problem happened since new, had repairmen twice and they did nothing but move the dishwasher stating it needed alignment, never mentioned this easy repair....
two screws that hold D/W to countertop, pulled D/W out enough to remove the old latch, install new latch, push D/W back into place, rescrew to counter top and rescrew the two latch screws. This problem happened since new, had repairmen twice and they did nothing but move the dishwasher stating it needed alignment, never mentioned this easy repair....
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jake from SACRAMENTO, CA
- Parts Used:
- WD22X33499
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
The heating element on our dishwasher burned the lower spray arm, melting it in 2 pieces
Simply unscrewed the old damaged arm and screwed the new one on, took less than a minute
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Maurice from SAN JOSE, CA
- Parts Used:
- WD12X32798
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Dispenser no longer opened during wash cycle
Very straight forward. After removing the power source the dishwasher was pulled forward enough to access the the door hinge springs. Then the door could be removed and the inner skin separated to access the the dispenser mounting screws.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ryan from Saint Joseph, IL
- Parts Used:
- WD15X26140
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers
No water in dishwasher
It took longer to uninstall and reinstall the dishwasher than it did to change out the part
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ed from TRAVELERS RST, SC
- Parts Used:
- WD22X33499
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Lower spray arm had melted tips
A quick twist of the locking nut
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Alvin from SCHENECTADY, NY
- Parts Used:
- WD05X30818, WD21X10519
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Nutdriver, Screw drivers, Socket set, Wrench (Adjustable)
No heat in both water and air
Followed troubleshooting procedure to determine that defective Flood Switch caused the problem and not the Heating Element. Replaced only the Flood Switch. I also replaced a deteriorated door gasket.
De-installed dishwasher from cabinet, removed door, and tipped unit over with back of tub resting on floor.
I followed the document referenced here for the troubleshooting and repair procedures: GE Appliances Technical Service Guide, 2012 GE Dishwasher, 31-9226.pdf available on web.
De-installed dishwasher from cabinet, removed door, and tipped unit over with back of tub resting on floor.
I followed the document referenced here for the troubleshooting and repair procedures: GE Appliances Technical Service Guide, 2012 GE Dishwasher, 31-9226.pdf available on web.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- LaRay from PRESCOTT, AZ
- Parts Used:
- WD12X32798
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
soap did not dispense correctly
Followed video instructions step by step.
I was fortunate i had enough slack in water, electric and discharge lines to avoid disconnecting.
Two wrinkles
1. wire clips on my door had to be pulled/pried loose from door and there were two not one
2. could not slide dishwasher out after lowering adjusters and figured out it was the mounting tabs bumpimng the granite countertop, thus the use of putty knives to slide the dishwasher out.
I was fortunate i had enough slack in water, electric and discharge lines to avoid disconnecting.
Two wrinkles
1. wire clips on my door had to be pulled/pried loose from door and there were two not one
2. could not slide dishwasher out after lowering adjusters and figured out it was the mounting tabs bumpimng the granite countertop, thus the use of putty knives to slide the dishwasher out.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dawn from JAMESTOWN, TN
- Parts Used:
- WD21X10490
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Door did not latch, therefore would not operate
Replaced latch
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lonnie from YUKON, OK
- Parts Used:
- WD01X10569
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
REPLACE DOOR CABLE
Removed the top two screws that hold the dishwasher to the cabinet , remove the two screws on the bottom panel and remove the panel. Screw the levelers all of the way up and pull out the dishwasher about 6 to 8 inch. Hook the new cabe on the spring and pull around pulley and attach it to the door bracket. I replaced both cables. Reverse to complete.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ivan from MANSFIELD, TX
- Parts Used:
- WD19X25187
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Dishwasher Not Draining
The pump went out after a few months of very loud noise during the drain cycle and then one day no drain or noise. A bit of research shows that this pump goes out frequently on this model so I ordered a new pump after inspecting the old pump for a clog or snag on the rotors.
The Install:
After removing the dishwasher from it's installed location and turning it on it's side (unplug water and electric of course), I was able to remove the pump from the two lines that connected it to the dishwasher and the drain line. I also had to unplug the pump from an electric connection to the dishwasher. Swapping out the new pump was the same but in reverse. Not a hard install, only simple tools required.
One note, my electric connection to the dish washer was different on this model pump since they changed the original part but there is an adapter included with this part so make sure it is in the box and fits before beginning.
The Install:
After removing the dishwasher from it's installed location and turning it on it's side (unplug water and electric of course), I was able to remove the pump from the two lines that connected it to the dishwasher and the drain line. I also had to unplug the pump from an electric connection to the dishwasher. Swapping out the new pump was the same but in reverse. Not a hard install, only simple tools required.
One note, my electric connection to the dish washer was different on this model pump since they changed the original part but there is an adapter included with this part so make sure it is in the box and fits before beginning.
Was this instruction helpful to you?
Thank you for voting!