GDF570SSF4SS General Electric Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- William from NORTH ANDOVER, MA
- Parts Used:
- WD21X22276
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Main Control Board needed replacing
Shut Power off at Circuit Breaker
1. Remove Kick Plate & Insulation
2. Unplug electrical connection from door to unit
2. Remove 2 screws with nut driver to release panel above electrical connection box
3. Pull panel down and out to expose board
4. Disconnect 3 plugged wire leads
5. replace old board with the new in the tray
6. Plug connectors in
7. Put unit back together
1. Remove Kick Plate & Insulation
2. Unplug electrical connection from door to unit
2. Remove 2 screws with nut driver to release panel above electrical connection box
3. Pull panel down and out to expose board
4. Disconnect 3 plugged wire leads
5. replace old board with the new in the tray
6. Plug connectors in
7. Put unit back together
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lynn from TOPEKA, KS
- Parts Used:
- WD28X26099
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Old tray was rusting.
Simply pulled the new one out of the box and put it into the dishwasher.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kristin from CONROE, TX
- Parts Used:
- WD35X20794
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Upper spray arm broke off and melted on heating element
Popped old bracket off with screwdriver, with a then easy installation of the new part.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Howard from PORT TOWNSEND, WA
- Parts Used:
- WD35X20794
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Upper Spray Arm broke in half from hitting something in the upper rack.
Had to remove the rubber gasket on the new spray arm to install the device, as it was hard to push into the above slot that fits the arm..
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lonnie from YUKON, OK
- Parts Used:
- WD01X10569
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
REPLACE DOOR CABLE
Removed the top two screws that hold the dishwasher to the cabinet , remove the two screws on the bottom panel and remove the panel. Screw the levelers all of the way up and pull out the dishwasher about 6 to 8 inch. Hook the new cabe on the spring and pull around pulley and attach it to the door bracket. I replaced both cables. Reverse to complete.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Patrick from BROOKFIELD, WI
- Parts Used:
- WD21X10490
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Dish washer would not turn on
took off 2 sheet metal on the bottom, lowered the dish washer, pulled it out enought to unscrew 2 screws, unplugged the old part plugged in the new, put it back together.
Works like a champ.
Works like a champ.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Herminio from TOMS RIVER, NJ
- Parts Used:
- WD21X10490
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Socket set
Door 1witch stopped working
1. Turned off circuit breaker
2. Pulled out dishwasher
3. Disconnected switch and popped out switch
3. Popped in new switch and connected
4. Pushed dishwasher back into place
5. Turned on circuit breaker
6. Turned on dishwasher and it worked
2. Pulled out dishwasher
3. Disconnected switch and popped out switch
3. Popped in new switch and connected
4. Pushed dishwasher back into place
5. Turned on circuit breaker
6. Turned on dishwasher and it worked
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from DELAND, FL
- Parts Used:
- WD22X33498, WD22X33499, WD35X20794
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
Knocking sound during wash cycle
Replace all three spray arms and knocking sound disappeared.
Unscrewed counter clockwise old sprayer arms and lifted. Replaced with new sprayer arms and noise disappeared.
Unscrewed counter clockwise old sprayer arms and lifted. Replaced with new sprayer arms and noise disappeared.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- BENJAMIN from ONALASKA, TX
- Parts Used:
- WD12X26146
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
3 Plastic rollers on bottom of dish basket came off and melted by the heating coil in dishwasher,
Simply pick the basket up to slide wheels onto axles and push in until they lock in place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stephanie from Huntsville, AL
- Parts Used:
- WD12X32798
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers
The soap dispenser was not opening during the washing cycle
Took off the door and separated the two door pieces. Unscrewed the old dispenser and replaced it with the new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ryan from Saint Joseph, IL
- Parts Used:
- WD15X26140
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers
No water in dishwasher
It took longer to uninstall and reinstall the dishwasher than it did to change out the part
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- GARY from SOAP LAKE, WA
- Parts Used:
- WD12X32798
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
The soap dispenser was broken os to save money I ordered one on-line
The repair instructions were great and the repair went well. The repair took less than an hour.
Thank you
Gary
Thank you
Gary
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Neil from NEW YORK, NY
- Parts Used:
- WD08X22095
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
Dishwasher door was leaking at bottom.
When new gasket arrived almost two weeks after it was sent out from Green Bay, I took out old gasket, marking which side was in and which out.
Then, with hands, fit new gasket in place making sure it was centered.
No leaking; it worked.
Thanks.
Then, with hands, fit new gasket in place making sure it was centered.
No leaking; it worked.
Thanks.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from STEWARTSTOWN, PA
- Parts Used:
- WD35X10386
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- More than 2 hours
Not fault of Parts Select - WARNING you cannot fix dishwasher with this part.
This is NOT a complaint about Parts Select (GE however has some packaging issues to resolve). It may become a complaint of Parts Select if not resolved to my full refund.
Unable to repair with provided part.
I have performed this repair in the past easily and successfully with part from GE Parts. GE Part Number: WD18X10052
GE Parts currently lists part number above as discontinued with a new GE Part
Number: WD35X10386. However not in stock
Found new part number locally however was missing the hose and plastic molded tubing that connects to pump and provides the actual diverter mechanism. Obviously did not purchase.
Ordered from Parts Select on 2021-12-22 and inquired if their part was complete. I was assured it was and paid for overnight shipping at approximate cost of $30.
Part arrives on Christmas Eve, a day late and incomplete. Called Part Select and was assured I would be reimbursed for full cost of part and shipping and was provided with shipping label to return incomplete part at their cost once their stock personnel verifies my claims.
I have photos of original/damaged but complete part beside new in package incomplete part for record and your use if you request.
Email Greg at:
One_US.Marine@yahoo.com
Unable to repair with provided part.
I have performed this repair in the past easily and successfully with part from GE Parts. GE Part Number: WD18X10052
GE Parts currently lists part number above as discontinued with a new GE Part
Number: WD35X10386. However not in stock
Found new part number locally however was missing the hose and plastic molded tubing that connects to pump and provides the actual diverter mechanism. Obviously did not purchase.
Ordered from Parts Select on 2021-12-22 and inquired if their part was complete. I was assured it was and paid for overnight shipping at approximate cost of $30.
Part arrives on Christmas Eve, a day late and incomplete. Called Part Select and was assured I would be reimbursed for full cost of part and shipping and was provided with shipping label to return incomplete part at their cost once their stock personnel verifies my claims.
I have photos of original/damaged but complete part beside new in package incomplete part for record and your use if you request.
Email Greg at:
One_US.Marine@yahoo.com
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Marlene from FT WASHINGTON, MD
- Parts Used:
- WD35X20794
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
new dishwasher with broken upper spray arm
The part did not fit at all but not worth it to me to return it. The part I need is about 20 inches in length and the one sent was about 10 inches. I will simply call for this dishwasher to be repaired or replaced.
Was this instruction helpful to you?
Thank you for voting!