GDF620HSJ0SS General Electric Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Daniel from CONCORD, NC
- Parts Used:
- WD21X10519
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Dishwasher wasn't heating water
So after noticing some horrid food waste build up in my 9 year old dishwasher, I determined it wasn't heating the water during the wash cycle. I came on here to check how to replace the heating element and was surprised when the flood switch was instead strongly recommended as the first repair step.
I ordered the part, and prepped the dishwasher for the repair (Pro-tip: Clothes pin attached to the bottom of the flood switch wiring harness ensures it doesn't slip down below the opening during the part swap!). The part swap and reassembly only took 5-10 mins or so after prep and dishwasher is now heating water and running great again. Many thanks to partselect.com for the detailed installation guides/videos and the parts recommendations!
I ordered the part, and prepped the dishwasher for the repair (Pro-tip: Clothes pin attached to the bottom of the flood switch wiring harness ensures it doesn't slip down below the opening during the part swap!). The part swap and reassembly only took 5-10 mins or so after prep and dishwasher is now heating water and running great again. Many thanks to partselect.com for the detailed installation guides/videos and the parts recommendations!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joe from Rio Verde, AZ
- Parts Used:
- WD22X33499
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Lower arm spray had hole melted in it
Simply put it on and twist it to lock in place. Took all of 3 seconds
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- CURT from SHELBY TWP, MI
- Parts Used:
- WD28X34744
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Lower dish rack rusted out
Took it out of the box and set rollers on track
rolled in place ALL DONE
rolled in place ALL DONE
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lori from ALLENDALE, MI
- Parts Used:
- WD21X31902C
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
The control panel went out
READ THE INSTRUCTIONS THAT COME WITH THE PART! After taking the dishwasher apart and installing the new part...it still didn't work. Then we read the instructions that came with the part. There are different settings on the part depending on your model of dishwasher. We removed the part, set it to our dishwasher, and it works perfectly. The job could have been quicker if the instructions had been read first.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mike from FRESNO, CA
- Parts Used:
- WD05X30818, WD21X10519
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers, Wrench (Adjustable)
Dishwasher not heat or drying dishes
Turned off pier at breaker. Removed dishwasher from under counter after disconnecting water line from dishwasher and drain tube from under sink. You might get a little residual water but not much. Removed old flood switch took about 2 minutes. Replaced with new flood switch. Then tilted dishwasher back to get to plastic nuts that hold down heating element. Set unit back down and removed old heating element then replace it with new one. Replace plastic nuts that hold element. Exact parts makes job easy. Them put water hose back on an put washer back in place hooked drain hose back up. Turned water and power back on. Tested unit worked perfectly. Hardest part of job was putting the dishwasher back into counter and getting the Instalation back on top.
Parts replacement time was about 10 minutes.
Disconnecting and reconnecting and replacing dishwasher 40 minutes. But I wouldn’t pay anyone to do this because it’s really not difficult.
Parts replacement time was about 10 minutes.
Disconnecting and reconnecting and replacing dishwasher 40 minutes. But I wouldn’t pay anyone to do this because it’s really not difficult.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Alan from NEOSHO, MO
- Parts Used:
- WD21X31902C
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
No power to the control panel
Removed the door to get to the UI control panel. Followed the instructions to set the jumpers to my particular model and put it back together. Fixed the issue and worked perfectly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from MONMOUTH BCH, NJ
- Parts Used:
- WD21X31902C
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Control board would not properly work and light up
Followed a u-tube video to remove dish wash door assembly to get to the control board . Not too hard if you are mechanically inclined.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Earl from WINCHESTER, TN
- Parts Used:
- WD19X25187
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set, Wrench (Adjustable)
Water would not drain.
Unhook water line . Turn off power to dishwasher. Remove dishwasher from under counter. Lay it on its back. Loosen clamps on drain pump and remove pump. Install new drain pump and tighten clamps. Be sure to put hanger in the hole on the pump. Very easy job. Reinstall water line and put dishwasher back under counter. Turn on power to dishwasher. Go to go.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- BENJAMIN from ONALASKA, TX
- Parts Used:
- WD12X26146
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
3 Plastic rollers on bottom of dish basket came off and melted by the heating coil in dishwasher,
Simply pick the basket up to slide wheels onto axles and push in until they lock in place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- PeggyAnn from EAST DUBLIN, GA
- Parts Used:
- WD13X10071, WD21X10490
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
broken latch
My son did the repair, I ordered both latch and striker, only needed the latch...only took him a few minutes to remove the old and install the new and works just fine
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gary from CONNEAUT, OH
- Parts Used:
- WD22X20688
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
the hub that holds the spinner for the top water in the dishwasher broke
the design of this part is easy to break when closing the top rack.
there is a hub that clicks in place and a spinner within this that makes the water spray evenly on the top of the tub of the dishwasher
the part broke when closing the rack [a dish too tall hit it]
it took less than 5 minutes to replace as the part just clicks into two edge spots i did this without removing the rack or even looking into the tub all by feel
there is a hub that clicks in place and a spinner within this that makes the water spray evenly on the top of the tub of the dishwasher
the part broke when closing the rack [a dish too tall hit it]
it took less than 5 minutes to replace as the part just clicks into two edge spots i did this without removing the rack or even looking into the tub all by feel
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mike from WADSWORTH, OH
- Parts Used:
- WD49X24057
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Old filter had calcium deposits that would not come off with soaking and scrubbing. That restricted water flow.
Simply twist on the new part/filter.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steve from Park Hill, OK
- Parts Used:
- WD22X33499
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Large hole in spray arm
Popped the old one off. Popped the new one on. Easy as that.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mason from JESSIEVILLE, AR
- Parts Used:
- WD22X33499
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Lower spray arm locking lugs had worn and it would pop off when the dishwasher was in use. It fell on the heating element during the dry cycle and a hole was melted through it.
I took out the old one and simply inserted the replacement. It was an exact replacement part and thus a perfect fit. Dishwasher is working fine now! Cost was around $40 (shipped) which I thought was reasonable.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Benjamin from VIENNA, VA
- Parts Used:
- WD21X10519
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers
The dishwasher was filling normally, but was not heating the wash water nor heating the dishes for the final dry. Dishes were not being properly cleaned and were not at all dry after the cycle.
I replaced the flood switch following instructions shown in readily available YouTube videos. In short, you remove the coarse and fine filters, then take out the bracket holding in the flood switch and finally the switch itself. After replacing the switch, the dishwasher works normally again.
Was this instruction helpful to you?
Thank you for voting!