GDF610PMJ2ES General Electric Dishwasher - Instructions

Release DW from cabinet and pull out, Unplug power.
Remove kick plate and unplug door cable.
Open door about 6 inches and using socket back out 2 bolts at bottom of door corners.
Pull door up off hinges about 4 inches and slide old gasket out and install new gasket in place.
Reset door on hinges and reinstall bolts.
Plug door cable in and reattach kick plate and plug power cable in.
Push DW back in place and attach to cabinet and adjust kick plate

Repair was straightforward. You can change water inlet on this model from underneath in bottom from, although it is a little tight

1. Turned off circuit breaker
2. Pulled out dishwasher
3. Disconnected switch and popped out switch
3. Popped in new switch and connected
4. Pushed dishwasher back into place
5. Turned on circuit breaker
6. Turned on dishwasher and it worked

This is a replacement that is straightforward but a bit mechanical. For an experienced engineer it was no problem but for the common household this is a repair best left to the pros. Fixed the issue no problem and the dishwasher is working perfectly now.

Replaced motherboard, parts select,very helpful in helping diagnose problem! Exchanged parts, credit account after returned parts. Great customer service All good stuff! They brought their A game for this diy-er...

Got the seal, read the reviews to see how to do it, Take out the two bottom screws ,easy enough. pull the door up ,pull out seal replace new one. Easy enough, but know one said don't pull the door up too high , I did, could not get it back down to save my soul. Needles to say had to buy a new dishwasher. that sucked have the new seal gasket if anybody needs one

I replaced the flood switch following instructions shown in readily available YouTube videos. In short, you remove the coarse and fine filters, then take out the bracket holding in the flood switch and finally the switch itself. After replacing the switch, the dishwasher works normally again.

Chances are your Lower spray arm is worn or jets are off. Replacing this part is very easy. Grab the base of the lower spray arm, twist and pull straight up. Place the new one in and twist lock in place. Repair complete!

-Disabled power.
-1/4” nut driver to take off kickplate.
-Unplug wires harness to door
-Dismount dishwasher from cabinets and pull out 4-6 inches
-uncouple spring pulley from door hinges.
-Open dishwasher door about 4 inches and pull out and up to remove
-Lay door down and remove 4 -T20 star bolts and two 1/4” bolts from door hinges(the door hinge has four bolts, but only remove one from each hinge that connects to the inner plastic door)
-remove vent cap and push up on interior plastic door casing to separate outer and inner door.
-Unbolt the soap dispenser module via 1/4” bolts and replace with new module. (be sure to line up module and gasket properly, installing 1/4inch bolts crossways, slowly tightening each bolt for a perfect seal).
-Reassemble the inner/outer doors and reattach to dishwasher in reverse order.
Be sure to plug the doors electric harness and kickplate.
-Plug the dishwasher back in and run it through a test.

I recently replaced the user interface, which took about 30 minutes. A week later replaced the soap dispenser module, which took 20 minutes. Disassembling the door was easier the second round.

I would read this project very easy for somebody with technical skills and easy with no prior skills

Took cover of door off. Removeddoor from frame 1st. Lift door off of hinge. Disconnect door from springs. Unscrew bottom screws at base of door. Lift front cover(actually slides down) remove old part replace with new.make sure unplug door from main body.

Simply twist on the new part/filter.

Took bottom plate off pulled down controls module plate

Make sure power to dishwasher is off. Unscrew from counter. Pull dishwasher out enough to expose pulleys that hold the door in place. Remove lower panel and insulation. Unplug door jack from main panel underneath. Loosen pulleys on each side and remove door. Take a 1/4 in socket and remove the bolt on the upper side of the hook on each side, then remove the screws on the outer side panel on each side. Now slide the inner door panel up (push the top and pull the bottom), which will release the hooks on each side. Turn over the inner panel and remove the four screws that hold the interface control panel in place. Unplug the two jacks and remove the panel. Now take a small flat-head screwdriver to remove the clear cover. Remove the control panel. Make sure you set the junction as prescribed with the instructions that come with the new control panel. MIND YOU- YOU HAVE TO REMOVE THE JUNCTIONS (TAKE EACH ONE OUT) AND RESET THEM ON THE PRONGS IN THE ORDER AS PRESCRIBED. Replace the control panel, replace the clear cover, insert it back in place, plug in jacks and replace screws. Turn inner panel over and line up side where the hooks lock. replace all screws and bolts. Replace door on dishwasher, plug in jack to main panel, attach pulleys to door. Replace insulation and front panel to bottom of dishwasher. Push dishwasher back in place. Replace screws that hold dishwasher to counter. Turn main power back on and VOILA!!

Unscrew the upper and side holding screws. Move dishwasher part way out. I didn't need to disconnect the water or electric. Make sure the electricity is off. Remember your working around water. Take off the bottom plat removing two screws, Remove broken cable pulley and replace new. Buy two since your their you might want to replace both. Have fun! It's duck soup.

Had authorized GE repair service come too fix my dishwasher. He diagnosed problem to be mother board .coast $99 for house call. He did some calculations and said it will be $550 for parts and labor. I found parts select online and ordered part for only $80
And made repair myself. Simple ,a few hex screws and unplug mother board it was a snap.