GDF520PGD4CC General Electric Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Raymond from SOMERSET, NJ
- Parts Used:
- WD21X22276
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers, Socket set, Wrench (Adjustable)
washer would not turn on - start button light would flash but not turn washer on
The main board is located under the washer in metal box accessed by removal of front plate at bottom. Removal of 2 screws on front of metal box allows board to drop down. However, very cumbersome to work on your back on floor in small space. I took the easy way and slid the washer out of cabinet, then turned washer ( it's light weight) on its back to access & remove old board and easily replace with new one. Also one of the connector plugs had to be replaced wired into the power connection made me very glad I was not working on my back ! Then simply turn washer upright and slide back into its cubby hole under counter.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Daniel from WATERBURY, CT
- Parts Used:
- WD28X22621, WD21X10519
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Dish washer wasn't getting the water hot to wash or dry
In did the drain screen, undid two nuts on top, removed panel, undid plastic ring, undid two screws with but driver, pulled sensor up, dried up any water at bottom, installed new sensor and follow steps in reverse. It worked!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Aston, PA
- Parts Used:
- WD22X33499
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Water leak corners of door onto the floor
After hours looking for problem. I tried cleaning door gasket. Did not stop leak. Looked at lower water spray arm and it was split. It is literally a 2 minute repair to remove and install. Knock on wood, no leaks in the last 10 washes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lynn from TOPEKA, KS
- Parts Used:
- WD28X28918
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Old tray was rusting.
Simply pulled the new one out of the box and put it into the dishwasher.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stephanie from Huntsville, AL
- Parts Used:
- WD12X32798
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers
The soap dispenser was not opening during the washing cycle
Took off the door and separated the two door pieces. Unscrewed the old dispenser and replaced it with the new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph from KENNEDALE, TX
- Parts Used:
- WD22X33499
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Loud banging sound when dishwasher was on.
The base of the spray arm literally just spins a little bit into place like a luer lock. Takes two seconds to replace.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from CLIFFSIDE PK, NJ
- Parts Used:
- WD22X33498, WD22X10090
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Kept falling off during use.
Just took old one off & install new one. Snaps on dish rack. Took 5 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from DELAND, FL
- Parts Used:
- WD22X33498, WD22X33499, WD35X20794
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
Knocking sound during wash cycle
Replace all three spray arms and knocking sound disappeared.
Unscrewed counter clockwise old sprayer arms and lifted. Replaced with new sprayer arms and noise disappeared.
Unscrewed counter clockwise old sprayer arms and lifted. Replaced with new sprayer arms and noise disappeared.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Peter from N HOLLYWOOD, CA
- Parts Used:
- WD08X21894
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers
old nasty gasket needed to be replaced
youtube youtube youtube!
No videos for the exact unit, but I got the gist from one video which included the trick of holding the door hinge springs in place with allen wrenches, while the door slid up and away for access to the gasket. I also had to pull the unit out from under the counter by about a foot. No need to disconnect anything. Good luck.
No videos for the exact unit, but I got the gist from one video which included the trick of holding the door hinge springs in place with allen wrenches, while the door slid up and away for access to the gasket. I also had to pull the unit out from under the counter by about a foot. No need to disconnect anything. Good luck.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charles from MYRTLE BEACH, SC
- Parts Used:
- WD28X35779, WD28X28918
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Racks were rusted.
Ordered new parts, unpacked the shipping containers, removed old racks and inserted the new ones. piece of cake. Perfect fit and prompt service.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ANNE from LAKE PLACID, FL
- Parts Used:
- WD28X28918
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Original lower rack rusted
Pulled out old rack and replaced with new rack.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kenneth from SEBRING, FL
- Parts Used:
- WD22X33498, WD22X33499
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
All 3 spray arms were stoped up.
Replaced all 3 spray arms in less than 10 minutes.The top one came in two pieces,the mounting bracket and the arm.Snap the bracket on the dishwasher first , then attach the arm to the bracket.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Randal from TWIN FALLS, ID
- Parts Used:
- WD21X10519
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Socket set
Wife said Dishes were not Drying and leaving Spots !
I tested Heating Element with Ohm Meter-Direct Short (if open it would have been bad and I would need to replace the element. Per the Website Troubleshooting for GE dishwasher, it said Heating Element (65%), Float Switch (32%), or Computer Board (only 3% Chance of it being board). So I ordered Float Switch. Later I noticed that the dishwasher would not change wash cycles from Heavy, Normal or Light.
So I turned the Circuit Breaker on and off. This fixed the Wash Cycle.
When the Float Switch Came in, I installed it in a few minutes watching the video on the GE Troubleshooting Page. Later when it was running I checked the operation and when I opened the door, the wife says seeing the steaming water, You fixed it, the Water is Hot now ! It was all about Hot Water, not the Heating Element at all ! And I think everything was fixed when I flipped the Circuit Breaker on and off and re-set the computer board. I think replacing the Float Switch was good maintenance, cause it was really dirty and needed to be replaced soon anyway. And it may have avoided my wife's next misdiagnosis with our dishwasher. This was 2 weeks ago, and all is well.
Sincerely,
Scott
So I turned the Circuit Breaker on and off. This fixed the Wash Cycle.
When the Float Switch Came in, I installed it in a few minutes watching the video on the GE Troubleshooting Page. Later when it was running I checked the operation and when I opened the door, the wife says seeing the steaming water, You fixed it, the Water is Hot now ! It was all about Hot Water, not the Heating Element at all ! And I think everything was fixed when I flipped the Circuit Breaker on and off and re-set the computer board. I think replacing the Float Switch was good maintenance, cause it was really dirty and needed to be replaced soon anyway. And it may have avoided my wife's next misdiagnosis with our dishwasher. This was 2 weeks ago, and all is well.
Sincerely,
Scott
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Russ from SPRING, TX
- Parts Used:
- WD28X28918
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Old lower rack was rusted
Opened the box took the rack out and placed it in the dishwasher. Good as new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- robert from WAUSAU, WI
- Parts Used:
- WD28X28918
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
Lower dishwasher rack was rusted through
The dishwasher rack was supposed to come with wheels it did not but I was able to use the existing wheels from the lower rack and snap them on was pretty easy
Was this instruction helpful to you?
Thank you for voting!