DDT575SGF4BB General Electric Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Donald from NASHVILLE, TN
- Parts Used:
- WD21X10490
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Dishwasher door sensor/ mother board
Replaced motherboard, parts select,very helpful in helping diagnose problem! Exchanged parts, credit account after returned parts. Great customer service All good stuff! They brought their A game for this diy-er...
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steve from Park Hill, OK
- Parts Used:
- WD22X33499
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Large hole in spray arm
Popped the old one off. Popped the new one on. Easy as that.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kathleen from Vero Beach, FL
- Parts Used:
- WD28X28918
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
lower rack was getting rusted
Took out of box and slipped old one off and new one in. That easy and I am 83 years old. Took maybe 5 minutes to install.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mike from WADSWORTH, OH
- Parts Used:
- WD49X24057
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Old filter had calcium deposits that would not come off with soaking and scrubbing. That restricted water flow.
Simply twist on the new part/filter.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sau from NILES, IL
- Parts Used:
- WD15X26140
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Socket set
Dishwasher would have water left inside over a few days
Repair was straightforward. You can change water inlet on this model from underneath in bottom from, although it is a little tight
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from CASTLE ROCK, CO
- Parts Used:
- WD01X10569
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
The pulley cable had broken
Unscrew the upper and side holding screws. Move dishwasher part way out. I didn't need to disconnect the water or electric. Make sure the electricity is off. Remember your working around water. Take off the bottom plat removing two screws, Remove broken cable pulley and replace new. Buy two since your their you might want to replace both. Have fun! It's duck soup.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Benjamin from VIENNA, VA
- Parts Used:
- WD21X10519
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers
The dishwasher was filling normally, but was not heating the wash water nor heating the dishes for the final dry. Dishes were not being properly cleaned and were not at all dry after the cycle.
I replaced the flood switch following instructions shown in readily available YouTube videos. In short, you remove the coarse and fine filters, then take out the bracket holding in the flood switch and finally the switch itself. After replacing the switch, the dishwasher works normally again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mason from JESSIEVILLE, AR
- Parts Used:
- WD22X33499
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Lower spray arm locking lugs had worn and it would pop off when the dishwasher was in use. It fell on the heating element during the dry cycle and a hole was melted through it.
I took out the old one and simply inserted the replacement. It was an exact replacement part and thus a perfect fit. Dishwasher is working fine now! Cost was around $40 (shipped) which I thought was reasonable.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mike from LAS VEGAS, NV
- Parts Used:
- WD21X10490
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Broken door latch and springs were not connected.
Looked up the replacement part on YouTube, watched a video and followed the instructions. Part ordered was the correct part and the video showed how to access for replacing. Watched a different video for hooking up the disconnected springs that allow the door to lower and close smoothly. Whole process for repairs was less than 30 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Edward from VENICE, FL
- Parts Used:
- WD21X10490
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Door would pop open after starting dishwasher numerous times before latching would catch.
Removed two latch screws and one electrical connection, Removed
two screws that hold D/W to countertop, pulled D/W out enough to remove the old latch, install new latch, push D/W back into place, rescrew to counter top and rescrew the two latch screws. This problem happened since new, had repairmen twice and they did nothing but move the dishwasher stating it needed alignment, never mentioned this easy repair....
two screws that hold D/W to countertop, pulled D/W out enough to remove the old latch, install new latch, push D/W back into place, rescrew to counter top and rescrew the two latch screws. This problem happened since new, had repairmen twice and they did nothing but move the dishwasher stating it needed alignment, never mentioned this easy repair....
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jake from SACRAMENTO, CA
- Parts Used:
- WD22X33499
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
The heating element on our dishwasher burned the lower spray arm, melting it in 2 pieces
Simply unscrewed the old damaged arm and screwed the new one on, took less than a minute
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ed from TRAVELERS RST, SC
- Parts Used:
- WD22X33499
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Lower spray arm had melted tips
A quick twist of the locking nut
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ryan from Saint Joseph, IL
- Parts Used:
- WD15X26140
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers
No water in dishwasher
It took longer to uninstall and reinstall the dishwasher than it did to change out the part
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from NORTH ANDOVER, MA
- Parts Used:
- WD21X22276
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Main Control Board needed replacing
Shut Power off at Circuit Breaker
1. Remove Kick Plate & Insulation
2. Unplug electrical connection from door to unit
2. Remove 2 screws with nut driver to release panel above electrical connection box
3. Pull panel down and out to expose board
4. Disconnect 3 plugged wire leads
5. replace old board with the new in the tray
6. Plug connectors in
7. Put unit back together
1. Remove Kick Plate & Insulation
2. Unplug electrical connection from door to unit
2. Remove 2 screws with nut driver to release panel above electrical connection box
3. Pull panel down and out to expose board
4. Disconnect 3 plugged wire leads
5. replace old board with the new in the tray
6. Plug connectors in
7. Put unit back together
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Raymond from SOMERSET, NJ
- Parts Used:
- WD21X22276
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers, Socket set, Wrench (Adjustable)
washer would not turn on - start button light would flash but not turn washer on
The main board is located under the washer in metal box accessed by removal of front plate at bottom. Removal of 2 screws on front of metal box allows board to drop down. However, very cumbersome to work on your back on floor in small space. I took the easy way and slid the washer out of cabinet, then turned washer ( it's light weight) on its back to access & remove old board and easily replace with new one. Also one of the connector plugs had to be replaced wired into the power connection made me very glad I was not working on my back ! Then simply turn washer upright and slide back into its cubby hole under counter.
Was this instruction helpful to you?
Thank you for voting!