DDT595SMJ0ES General Electric Dishwasher - Instructions

I watched a step by step video provided on the Fix It app. Easy to follow directions and only took minutes to tear apart and put back together. Didn't even require help from my husband. Although the latch and striker were not the problem, contacted parts select and they then recommended the electronic control board, they ordered it, had it shipped to me within a few days, another really easy fix I did using the You tube video. Fixed the problem lickety-split. I will never go without my fix it app. Entered all my appliances. Sure beats spending hundreds on appliance repairmen! Thank you Parts Select!

A noisy dishwasher and water coming from underneath was being caused by a torn hose that is factory connected to the diverter. It was a little difficult to see at first as the hose sits slightly kinked when in it's normal position. Access to the diverter involves removal of the circulation pump. I ordered a new diverter which comes with metal screw on clamps. The main difficulty in installing is the positioning and alignment of the diverter and pump. My first effort resulted in a ripping of the attached diverter hose as I attempted to secure. I ordered another diverter. This time I used a lubricant to allow movement of the connecting hoses and made sure to not overtighten the clamps. I used a small mirror to make sure that the various hoses sat properly. Alignment took a bit of time. I then gently tightened the hoses. I ran the dishwasher, and found a leak, meaning that I needed to tighten these clamps a bit more. This is a doable repair that needs patience. The dishwasher is now very quiet and runs great!

Started by removing dishwasher, including disconnecting power, water and drain line. Then turned washer on back. Electrical connector to old wash pump was a little tricky to remove as the release tab isn’t straightforward, I used a tiny screwdriver and jiggled it around till it came loose. The factory hose clamps (2) are crimped on, but if you can find the tail end you can work them loose with a screwdriver by prying the tail up from the body of the clamp. Once you have the electrical connector and the two clamps removed, the pump comes of easily with a twisting motion. The new wash motor came with new clamps (2 extra). When sliding the rubber boots on the new pump in place, it will require a twisting motion to position it correctly, make sure (I didn’t and had to go through the whole process twice) that the rubber boot is not folded under on the bottom where it’s hard to see. Tighten clamps carefully and don’t over tighten. Plug in electrical connector and you’re ready to reinstall dishwasher.

Shut off power at breaker, remove two screws anchoring DW to counter top . Slide DW out far enough to access door latch, disconnect electrical wiring plug, remove two Phillips head screws, install new door latch, repeat installation in reverse order.

the design of this part is easy to break when closing the top rack.

there is a hub that clicks in place and a spinner within this that makes the water spray evenly on the top of the tub of the dishwasher

the part broke when closing the rack [a dish too tall hit it]

it took less than 5 minutes to replace as the part just clicks into two edge spots i did this without removing the rack or even looking into the tub all by feel

Nightmare!!! The Striker latch did not pop out with a screwdriver as it was supposed to. The whole dishwasher needs to be disconnected and pulled out, then front door removed and totally disassembled to remove the screw to replace the striker latch. lots of work to replace a striker latch. Bad design!

Unplugged power.
Shut off water supply.
Remove the kick panel.
Unscrewed dishwasher from under cabinet and side screws. lower feet to reduce tension.
As you slide the dishwasher out, be sure all lines (Drain, water supply, electric are free to move with dishwasher.
I was able to hold the dishwasher at an angle to easily get to the valve. After removing the the valve, i screwed the new valve back into place. I removed the Line between the valve and Dishwasher. Putting the line on the new valve. I removed the water supply line from the old valve and installed it on the new valve.
Placed the dishwater back in place and screed it back in. I ran the cycles. everything works!
I replace the kickpaner a couple of hours later. Check to make sure there were now leaks.

The dishwasher was not heating anymore. I suspected it was the float/flood switch, so I got that ordered. I went ahead and ordered the element also and I'm glad I did! Even though the element was good, when I tested it I loosened the nut holding the element in. When I retightened it there was NO WAY for me to get it watertight again and it kept dripping out the bottom. Mine was made in 2019, and the gaskets on the element that came with it were a terrible design - the metal flange on the element was about as big as the hole in the middle of the gasket so water just leaked between the gasket "donut" hole and the element with no way to seal. The element I bought for this repair just in case had a totally redesigned gasket that sealed right up and didn't have the same design issue. So beware, if you are fiddling with the element in your process, be sure the gasket will reseal - or just have an extra new element in case it is the old (bad) design.

The flood switch was easy to find (with dishwasher on its back) in a white housing under the black circular sump.

Getting the actual switch out of that housing took some doing. I ended up using 4 small kebab sticks - toothpicks might work better- all 4 tabs have to be pulled out at the same time.

So I ended up changing out both the element (which was good but started leaking) and the float switch.

IMPORTANT!!! Before you put the dishwasher back in, you probably need to reset the thermal cutoff (TCO) on the back of the dishwasher. Follow the wire up from the element and it is the first thing it goes to. There should be a small (3mm) black button that has popped out. Press that back in. With your repair (float switch or element) it should start heating again - at least mine did.

Dishwasher is under 2yrs old and suddenly failed to drain due to the drain pump not working. I read the reviews on how easy it was to change and went ahead and purchased one. After removing the screw from the appliance bracket under the counter and the two screws from the base plate, it was easy to pull the dishwasher from under the counter and away to flip to its side. I would recommend draining the drain hose first and making sure no water is in the tub. Keep a towel nearby. Removing the drain pump was simple. I needed a nose tip pliers to remove one of the hose clamps and a screwdriver for the other clamp. Once the pump was removed, I opened the old pump by twisting the top part while pressing the tabs to remove upper housing. There was a broken piece of glass that had wedged itself in the mechanism which prevented the pump from working. I wish I had checked that first, before purchasing a new drain pump. I kept the old pump as a backup for the future. It took no more than 20 minutes to get the pump replaced and the dishwasher back in place. Dishwasher drains just as new. By the way, costed under $100 with delivery. An appliance repair company wanted $250!!
Not the first time PartSelect saved me money and won’t be my last!

This dishwasher started to not want to start about 1 year ago but on several attempts to start the dishwasher it would power up or start. On Christmas Eve 2021 I did a load of dishes and from that point on the dishwasher would not power up. Got on line and did some troubleshooting and felt the Control Panel was the problem. Ordered the replacement part from this website, the part arrived around January 1, 2022. Installed the new Control Panel yesterday and my dishwasher is now working great again. Thank you for the ability or order and fix my dishwasher

This is a replacement that is straightforward but a bit mechanical. For an experienced engineer it was no problem but for the common household this is a repair best left to the pros. Fixed the issue no problem and the dishwasher is working perfectly now.

Simply twist on the new part/filter.

Repair was straightforward. You can change water inlet on this model from underneath in bottom from, although it is a little tight

Process of elimination and a visit to my local repair store told me it was wise to try the tub gasket, and according to partselect.com, it solved the problem a majority of the time. My local repair dealer agreed: Try it. They agreed because for them to replace a lower door gasket AND the $10 tub gasket... if they came out, the service call and parts would equal half the cost to replace the whole dishwasher. So I bought a tub gasket from partselect.com and replaced the old one. It worked, it was easy, so if your same make & model is leaking? Try it first. That's my advice.

Took cover of door off. Removeddoor from frame 1st. Lift door off of hinge. Disconnect door from springs. Unscrew bottom screws at base of door. Lift front cover(actually slides down) remove old part replace with new.make sure unplug door from main body.