DDT575SSF8SS General Electric Dishwasher - Instructions

Parts diagram shows Striker can be popped out with screwdriver. Not true. It has a screw bolting it internally. Impossible to get to unless you disassemble the entire door. We took a power drill and small drill bit and bore it out like a cavity in a tooth. Needle nose pliers to extract the screw. Pretend your a dentist. Fixed it in 5 minutes. Replacement fit tight. A+

The repair made it necessary to remove the door of the dishwasher. Removing the door seemed to be a daunting task, but after watching a YouTube video I made myself aware of the necessary steps to complete the task.

- After turning off the power to the dishwasher, I removed the kickplate panel, this gave access the wiring going to the defective board, which I unplugged.
- Removed the screws securing the dishwasher to the counter, these are located at the top of the machine and are accessible by opening the dishwasher door.
- Pull the dishwasher forward a few inches.
- On each side of the door is a spring loaded device that holds the door from falling open when not latched. They can be identified as white plastic items with a cable connected to them. Once removed take care to not allow the door to fall open, instead, when opened slightly raise the door off the unit.
- Lay the door on the floor.
- There are three sheetmetal screws on each side of the door, using your nut driver remove these screws. They secure outside of the door to the inner door.
- Stand the door up on the floor and raise the outer door panel, there are several plastic clips on each side the slide into slots on the inner door panel. I found it a little difficult to separate the panels, but with gentle persuasion they came apart.
- Lay the inner panel on the floor with the exposed electrical components facing up.
- At the top of the inner panel is a black plastic cover protecting the electronic components, this where the control panel lives.
- Remove the sheetmetal screws that secures this plastic cover.
- There are two wiring harnesses, remove them.
- The defective component can be lifted out.
- Install the new control panel.
- Reassemble.

I had to replace a docking port. Parts Select had the part, labeled as stainless, just as this survey indicates. Well folks, the part I received is 100% plastic. It it the correct part, just not stainless. Should it have been stainless due to a faulty plastic design? I don’t know.

I used Parts Select for the simple directions for installation. I was eventually linked to a YouTube video for a completely different docking port. Does my part slip on? Does it press in? I don’t know.

Needless to say, this has been a cheap but frustrating ordeal that is not yet over. Thanks for having the stainless, but really plastic, part and for having directions for some other part available.

1. REMOVE LOWER FRONT KICK PANEL.
2. CHECK FOR 14VOLTS BETWEEN PIN 2 AND PIN 5= NO VOLTAGE.
3. LOWER CONTROL BOARD PANEL
4. REPLACE ELECTRONIC CONTROL BOARD.
5. CHECK FOR PROPER OPERATION.

First, drain as much water as possible using a shop vac or siphon. Unscrew two plastic lugs and food screen to release the metal *disk* found inside the dishwasher at the bottom. Then, remove the grey retainer ring found under the food screen.
Using the nut driver, remove two screws from the white plastic retainer ring at bottom the flood switch.
I used pliers to grip the ring to take it out.
**Dry everything in the "well" where the flood switch sits.**
Now, remove the bottom front cosmetic panel. This exposes the underside of the appliance. Locate the flood switch wire underneath and gently pull down the small black plastic tab which holds the wires in place. This allows more movement to make your job a little easier!
Pull up on the flood switch and simply unplug it and swap in your new switch! Replace everything as you found it, don't over-tighten your screws, and make your kids load that sucker! Hope this helps, and have a beautiful day!

After replacing UI board, I replaced the mainboard. still did not solve the problem. The element tested good and I had removed the flood switch, rinsed and blew it out so it rattled but the damage was done. Replacing it made the dishwasher heat water and heated during dry cycle. Removed fine filter, removed course filter, removed two screws with nut driver, removed flood sensor and then reversed. A year or so ago, the dishwasher flooded for no apparent reason, wondering if that was the beginning end of the switch!

The replacement dishwasher basket easily fit in my dishwasher. Easy to order. Quick delivery. Highly recommended.

Took out 2 screws that held machine in cabinet. Pulled out dishwasher about 4 inches. removed old latch and disconnected electric connection. Put in new latch, reconnected electric connection, replaced screws, pushed machine back in cabinet, replaced 2 screws that hold machine in place. Works like new!

Took out the old heating assembly and installed the new one
this did not solve my problem and I ended up buying a new dishwasher and returned the part
Spent as much in shipping to get the part and return it as the part cost itself
Next time I will just replace the dishwasher in the first place.

Popped in the new one and done!!!

I loved the service I received. The site pulled up the correct make and model basket I need for my dishwasher and gave me several options. I order with ease and it arrived within a couple of days. No tools required.

Performed all checks on youtube...water coming in, course and fine filter cleaned, drain pump working (heard it come on and no water present and cycle end). Swapped water inlet valve bc it was the cheapest poss fix $19. No luck. Ordered circulation pump and motherboard. Swapped pump, very easy with machine out and turned on its back. Temp reinstall and ops checked good. Contacted Partselect for return slip, emailed immediately and sent thru post office.

Removed old basket, put in recycle bin, placed new basket in dish washer. The damage to the original basket was my fault. I now know not to drop heavy knives point down into the basket.

installed new silverware basket