GSD2000F02WH General Electric Dishwasher - Instructions

I removed the plastic inner door liner, removed the timer assembly. Replaced both plastic parts, Detergent cup release arm and dispenser release timer lever. The most difficult part was reassembling the timer lever spring. Long nose pliers made it simple. Works like new.

Turned off power and water to dishwasher, removed kick plate to dishwasher, removed mounting bracket from frame rail of dishwasher, unplugged valve then used pliers to remove spring clamp on rubber line and used box wrench to remove water line attached to brass connection. There was a lot of calcium build up around screen and rubber O-ring and cleaning that may have fixed it but pulled off anyhow. One problem I had is that the old part would not come apart where the L-joint screwed into the collar that attaches to valve on old setup to allow new one to be bolted to it. So I looked at putting new valve on the old mounting bracket. That did not work after I got it apart as the new bracket is flat while the old is counter sunk...and the new valve has a larger footprint and would not fit flush to seal. So back to work bench and put valve in vise as the threads had plumbers pipe cement it looked like and they were tight. Got the two joints apart...cleaned with wire brush...sanded down mouth of brass collar that fits against O-Ring of new valve to make sure clean. Put teflon tape on all threads and tightened it all back up. Reconnected, plugged in, mounted to dishwasher and ran a full cycle with dishwasher pulled out so I could monitor any leakage from beginning. All is good...so slid back under sink and ran load with dishes...noticed water on floor. Freaked out...pulled it all out and valve was dry. I forgot to clean up the little bit of water that came out of lines when disconnected first time for repair... :) All is good now.

Immediately shut off water supply to the washer. After ordering and receipt ot part: Removed base panel, turned off power, disconnected wire, water supply line and screws attaching washer to kitchen counter. Pulled the washer out and turned it on its side with the valve on top. Removed and replaced the valve, returned the washer to the upright position, pushed it back under the counter, reconnected all services, screws to counter and base panel, turned on the water and power. Took two hours since I needed take a trip to the hardware store to replace a right angle water fitting .

Removed the existing inner door by removing screws along the edge of the inside door. Had trouble removing the door latch but after lifting it on one side of the plastic door fitting, it eventually lifted out. I also had some trouble getting the spring loaded soap door back into the replacement inner door. After playing with it for awhile I realized that the soap door should be in the open position when putting the spring latch back on. The soap door won't close until you get the entire inner door mounted and back on. I also want to note the the inside vent in the upper part of the inner door needs to be removed from the old inner door and installed in the new one. I missed that at first and it allowed condensation to get inside the door which caused the dishwashers alarm to go off during the dry cycle. One last note that I initially decided not to replace the existing sound proofing material in the new door based on advice from a website that stated that I wouldn't notice the sound difference. That was definitely untrue. I had to disassemble the door, replace the sound proofing and then it sounded fine. Overall it was a little difficult to figure out but considering how inexpensive the replacement door was compared with a having a service repairman come out, it was worth the trouble.

Key symptom: when the drain phase begins, there should be a satisfying "Thunk" from the solenoid. No Thunk=solenoid not working

At first, I found a metal band that was rusted and loose, replaced it but still had a leak. I went to the diagnosis section and identified another area of problem, ordered the part and got super quick delivery. With the help my wife I was able to pull apart, repair and get the unit to run and stay dry. Wife is happy because she loves the décor of our old but now dry dishwasher.

We we're installing a used dishwasher,had to take it back out and replace the water inlet valve.