GSD2200F01AD General Electric Dishwasher - Instructions

Researched problems on internet,based on info ordered part. Got it in 24 hrs.followed package directions. So easy and for less than a service call! Runs like a charm now.

Removed dish washer from cabinet area and snapped new clip into cable and hook into support.. The time that took the longest was to removed the screws to pull the unit out of the cabinet area.. Very easy fix...

Replaced the water-fill solenoid valve.

Removed existing gasket seal on door. Cleaned really well with a household cleaner around the gasket crease. Installed new gasket seal around door. Started with small notch in the middle of the gasket to center on top and then slowly fastened into door edge and slowly snug around bottom edge where the deal is notched and the the difficult part was to feel the seam again on the bottom to re attach seal after notch from corner. Rupert this on the other side of door.

after watching related video on partselect.com, diagnosis and repair couldn't have been much simpler!

the repair would have been much easier but the screws from the old inlet valve did not match the size of the holes on the new valve.

I firts turned off power to the diswasher through the circuit breaker panel. I removed the black tray at the bottom front of the dishwasher, removed the two screws attaching the water inlet valve, detached inlet and outlet water hoses as well as the eletric connector. I removed fitting from the old valve and installed in the new valve using some teflon tape. Installation is the reverse of the removal.

I removed the plastic inner door liner, removed the timer assembly. Replaced both plastic parts, Detergent cup release arm and dispenser release timer lever. The most difficult part was reassembling the timer lever spring. Long nose pliers made it simple. Works like new.

Before you due anything else...remove the water inlet valve, remove the 4 screws holding the water inlet coupling to the valve housing, remove the nylon filter (tight fit), and clean the debris from the filter. Re insert the filter, reassemble the valve housing and check for leaks. Clears most water flow problems.

Had to install a new door latch. The installation itself is really quite simple involving removing (separating) the inner door panel to access the latch assembly. The latch is removed by simple push through one slot with a screw driver and the new unit basically pops in through grooved slots. However, I did find it quite helpful to first (and during) review a YouTube video illustrating the replacement. Although it is largely a simple procedure, for the first-time "installer" there are still a few tricky nuances to be aware of.

I unscrewed the front of the door almost to the bottom hinges and removed the latch. Went on line and ordered a replacement. The replacement arrived in a couple days (yeh), was identical to the one I had removed. I could have used another hand but went ahead and replaced it myself. It worked perfectly and I screwed everything back in place. I'm a 73-year-old female, good at taking things apart but not always good at putting them back together but will try anything. Was elated that I could repair it and it actually worked. Great service from your company!

This repair was not difficult except that the part was hard to get to. You need to lay on the ground and the space is small to fit the tools in. It was especially difficult to squeeze the hose clamp on and off. If you are the handy sort and would not be intimidated by pulling the dishwasher out (like I was), then I recommend doing that. Changing the actual part was a breeze and self explanatory. Be sure to shut off the power and water supply to the dishwasher. Bring a towel to soak up residual water in the hose. Watch the video on this site, it was exactly what I needed to see! I was able to fix my mom's dishwasher! What a great feeling!

took the front covers off, used om meter as suggested after disconnecting the wire plug. discovered infinity, so as suggested, determined the valve defective. Ordered over the new valve from this company. After it arrived, took the old valve off by removing it from the bracket. Used the pliers to take the hose off, then unscrewed the supply hose by usung the adjustable wrench. Took the old valve to my shop vise to hold it firmly, then unscrewed the fitting, wrapped the tape suggested and installed it on the new valve. Took it back to the dishwasher, screwed the supply hose on, slipped the hose on and the clamp, turned on the water to check for leaks. Found non, so installed the valve on the frame, turned on the power and checked for filling. Itfilled fine and operated like it was supposed to. Put the front covers back on, and enjoyed praise from wife!!!

Turned off power and water to dishwasher, removed kick plate to dishwasher, removed mounting bracket from frame rail of dishwasher, unplugged valve then used pliers to remove spring clamp on rubber line and used box wrench to remove water line attached to brass connection. There was a lot of calcium build up around screen and rubber O-ring and cleaning that may have fixed it but pulled off anyhow. One problem I had is that the old part would not come apart where the L-joint screwed into the collar that attaches to valve on old setup to allow new one to be bolted to it. So I looked at putting new valve on the old mounting bracket. That did not work after I got it apart as the new bracket is flat while the old is counter sunk...and the new valve has a larger footprint and would not fit flush to seal. So back to work bench and put valve in vise as the threads had plumbers pipe cement it looked like and they were tight. Got the two joints apart...cleaned with wire brush...sanded down mouth of brass collar that fits against O-Ring of new valve to make sure clean. Put teflon tape on all threads and tightened it all back up. Reconnected, plugged in, mounted to dishwasher and ran a full cycle with dishwasher pulled out so I could monitor any leakage from beginning. All is good...so slid back under sink and ran load with dishes...noticed water on floor. Freaked out...pulled it all out and valve was dry. I forgot to clean up the little bit of water that came out of lines when disconnected first time for repair... :) All is good now.

Removed and inverted the DW. Removed the impeller, grinder, screen and seals then the actual shaft seal. Replaced with new parts in reverse order. Instructions provided with the seal kit were simple and excellent. They were right to the point.